ARAG bravo 350 Series

Other manuals for ARAG bravo 350 Series

Installation, Use And Maintenance Guide46 pages

Questions and Answers

E
Eric CuevasSep 15, 2025
What to do if unable to reach output volume value set for the automatic operation on ARAG Control Systems?
- R
  Ryan TranSep 15, 2025
  If you are unable to reach the output volume value set for automatic operation, it may be due to a wrong setup, the system not being adequately sized, or a control valve malfunction. Check the setup of the application rate and the row width. Also, check the maximum pressure valve adjustment, ensure the control valve is adequate, and verify the valve operation.
J
Jessica CoffeyAug 25, 2025
What to do if the instantaneous pressure is not displayed on ARAG Farm Equipment?
- S
  Stephanie DuarteAug 25, 2025
  If the instantaneous pressure isn't showing on your ARAG Farm Equipment, there could be a few reasons. First, check the setup of the pressure sensor. Secondly, ensure that the computer is receiving signals from the pressure sensor. Finally, verify the connections to the pressure sensor, as incorrect installation might be the cause.
H
hoffmanmichaelAug 26, 2025
Why is the displayed speed not precise on my ARAG Farm Equipment?
- R
  ruth77Aug 26, 2025
  An imprecise speed display on your ARAG Farm Equipment is often due to an incorrect wheel constant setup. Check the setup of the wheel constant.
I
iunderwoodAug 26, 2025
What to do if the display does not switch on ARAG Farm Equipment?
- M
  Michael KrauseAug 27, 2025
  If the display on your ARAG Farm Equipment doesn't turn on, first, ensure there is a power supply by checking the power supply cable connections. If the power is on, check if the computer is OFF and press the ON key.
J
jacobsbrandonSep 16, 2025
Why is the displayed tank level not precise on ARAG bravo 350?
- P
  Patricia HendersonSep 16, 2025
  If the displayed tank level is not precise, it may be due to the level sensor not being calibrated or wrongly installed. Perform the calibration and check the connections to the level sensor.
J
Joanna NelsonSep 23, 2025
What to do if during the tank calibration procedure, the sprayed quantity is always steady on zero in ARAG bravo 350 Control Systems?
- J
  Jenna DuffySep 23, 2025
  If, during the tank calibration procedure, the sprayed quantity is always steady on zero, it could be due to wrong installation, no flowmeter installed, or section valves and main control set to OFF. Check connections to the flowmeter, install the flowmeter on the system, and set section valves and main control to ON.
S
Sara ButlerSep 8, 2025
What to do if the display speed is not precise on ARAG Control Systems?
- J
  Justin RiversSep 8, 2025
  If the displayed speed is not precise, the setup of the wheel constant may be incorrect. Check the setup of the wheel constant.
A
Andrew BaileySep 9, 2025
Why is the instantaneous pressure readout inaccurate on ARAG Control Systems?
- B
  Benjamin SmithSep 9, 2025
  An inaccurate instantaneous pressure readout may be due to an incorrect setup of the full scale for the pressure sensor or a wrong installation of the pressure sensor. It's recommended to check the setup of the full scale for the pressure sensor and the connections to the pressure sensor.
S
Sheila SmithSep 2, 2025
Why valve controls take no effect on ARAG Farm Equipment?
- J
  Jesse WiseSep 2, 2025
  If the valve controls on your ARAG Farm Equipment aren't working, it might be because the valves are not connected. Connect the connectors.
A
Ashley FrostAug 31, 2025
How to calibrate the displayed tank level on ARAG Farm Equipment if it is not precise?
- L
  Leslie ButlerAug 31, 2025
  If the displayed tank level on your ARAG Farm Equipment is not precise, it might be due to the level sensor. Perform the calibration, and if that doesn't work, calibrate the level sensor again. Also, check the connections to the level sensor, as incorrect installation could be the cause.