Need help?Do you have a question about the Arctic Spas Summit and is the answer not in the manual?
General| Seating Capacity | 6-7 |
|---|---|
| Voltage | 240V |
| Amperage | 50A |
| Insulation | Full Foam |
| Heater | 4.0 kW |
| Energy Efficiency | Full foam insulation |
| Pumps | 2 |
| Electrical Requirements | 240V/50A |
| Shell Material | Acrylic |
| Cabinet Material | Synthetic Wood |
Covers risks like drowning, injury from suction fittings, and electrical hazards.
Details electrical supply requirements, GFCI/RCD, and distances from metal surfaces.
Discusses water temperature limits, pregnancy, alcohol, drugs, and medical conditions.
Provides essential warnings for user supervision, suction guards, infectious diseases, and entry/exit.
Explains the risks of prolonged immersion in hot water and its symptoms.
Details dimensions, heater, water capacity, dry weight, and electrical requirements for various spa models.
Ensuring a structurally sound and level surface for spa placement.
Recommendations for solid foundations and patio stones for outdoor installations.
Ensuring deck load capacity and consulting professionals for deck installation.
Requirements for AWP placement on solid surfaces and ensuring service access.
Emphasizes licensed electrician for hookups and adherence to local codes.
Highlights the necessity of GFCI/RCD breakers for safety and warranty.
Step-by-step guide for filling the spa and priming the jet system.
Instructions for adjusting chemicals, balancing water, and stabilizing temperature.
Guidance on testing sanitizer levels and setting the desired spa temperature.
How to activate the "Boost filtration system" for chemical dispersion.
Labels and describes main spa features like Topside Control, Waterspouts, and Jets.
Explains the function and adjustment of 5-inch hydro-massage jets for circular massage.
Describes 3-inch turbo jets for back, shoulder, and neck massage, including adjustment.
Details the Monsoon Jet for maximizing massage action on specific body areas.
Describes the optional Therapy Air System for an exhilarating bubble massage.
Explains the system's self-check upon powering up, including hi-limit probe status.
Identifies buttons for pumps, lights, settings, and display indicators.
Guides on starting pumps 1-5 and the blower, including speed control.
Instructions for setting temperature, changing units, and operating the light.
Explains how to lock the control pad and activate Boost Mode for chemical dispersion.
Details how to set filter duration, frequency, and ozone/Onzen cycles.
Lists common error codes and their descriptions for troubleshooting.
Step-by-step instructions for draining the spa water and preparing for maintenance.
Guidance on cleaning or replacing filter cartridges weekly and monthly.
Explains the filtration system, cartridge replacement, and recommendations for clarifiers/foam inhibitors.
Instructions for cleaning and maintaining spa pillows to extend their life.
Guidance on cleaning the acrylic shell and avoiding harsh chemicals.
Important notes regarding iron/copper staining and recommended cleaning products.
Steps for cleaning and conditioning the vinyl spa cover to maintain its appearance.
Maintenance advice for cedar and no-maintenance cabinets, including oiling and cleaning.
Step-by-step instructions for replacing the 12-volt underwater LED lights.
Guidelines for maintaining water quality when away for 7-14 days.
Recommendations for draining the spa to prevent freezing damage during cold weather.
Outlines three methods for updating spa software via App, webpage, or USB.
Addresses problems like no functions, no heat, poor jet pressure, and non-working lights.
Troubleshoots complete spa drainage and self-activation issues.
Introduces the three fundamental areas: filtration, sanitation, and chemical balance.
Explains how to test water using liquid kits or test strips and parameters to check.
Provides tips for accurate water testing, like sampling depth and cell cleaning.
Emphasizes safe handling, storage, and use of spa chemicals.
Instructions on how to add chemicals safely while pumps are running.
Introduces the maintenance program and the need to remove excess minerals.
Explains TA, its importance as a pH buffer, and how to adjust it.
Details pH levels, their importance, and how to adjust them for optimal sanitizer effectiveness.
Recommends CH levels and warns about calcium precipitation issues.
Explains the importance of sanitizers and recommends specific Arctic Pure products.
Provides safety precautions for using chlorine systems and handling pucks.
Outlines initial and weekly chemical additions for the chlorine system.
Details initial and weekly chemical additions for the bromine system.
Tables listing common water issues like cloudy water, foaming, and odor with their causes.
Provides solutions for common spa water problems such as cloudy water, odor, and irritation.
Details warranty coverage for spa shells, equipment, plumbing, and other components.
Covers warranty for spa covers, sound systems, and specialized systems like Onzen/Spa Boy.
Specific warranty details for Onzen and Spa Boy systems, including electrode and salt blend usage.
Outlines warranty conditions, exclusions, and responsibilities of the customer and dealer.
Outlines the three steps to connect the spa to a home network for remote control.
Provides a flowchart illustrating the connection process for onSpa and Web Connect.
Explains the capabilities of the onSpa app for controlling jets, temperature, filtration, and accessing manuals.
Defines onSpa as an advanced spa control system usable via smart devices.
Explains Web Connect as an extension of onSpa for internet-based spa control.
Lists benefits of Web Connect, including adjusting functions and accessing reference materials.
Defines EoP technology for data transmission over electrical wiring.
Defines WIFI Extender as a device to expand wireless network reach.
Explains connecting the spa via an Ethernet cable to a home router.
Describes myarcticspa.com as a web-based support system for Arctic Spa owners.
Illustrates the onSpa interface connection via Ethernet Over Power (EoP).
Illustrates the onSpa interface connection via a WIFI Extender.
Illustrates the onSpa interface connection via a LAN Cable.
Illustrates the Web Connect interface via Ethernet Over Power (EoP).
Illustrates the Web Connect interface via a WIFI Extender.
Illustrates the Web Connect interface via a LAN Cable.
Provides a flowchart for connecting onSpa via EoP.
Provides a flowchart for connecting onSpa via WIFI Extender.
Provides a flowchart for connecting onSpa via LAN Cable.
Introduces connecting the spa to the home network using EoP, WIFI Extender, or LAN Cable.
Details steps to access LLP to ensure dynamic IP address assignment for the spa.
Guides on scrolling through LLP settings, saving changes, and confirming IP address.
Explains the process of connecting the spa to the My Arctic Spa server via web page.
Flowchart for opening an account and registering the spa on the myarcticspa.com webpage.
Instructions for registering the spa on the My Arctic Spa server via the website.
Brief outline of the My Arctic Spa website features and benefits.
How to access the myarcticspa.com homepage and initiate user account creation.
Step-by-step guide for creating a new user account on myarcticspa.com.
Instructions for logging in for the first time after account creation and spa connection.
Details on registering the spa by linking it to the user account via the topside controller.
How to log in to the My Arctic Spa account after initial registration.
Overview of the My Arctic Spa page, including monitoring spa status and adjusting settings.
How to access and adjust spa settings like filtration, Spa Boy, Ozone, and Power Management.
How to find manuals, guides, and quick reference cards on the documentation page.
Provides access to descriptions, causes, and solutions for spa error codes.
Displays spa information such as firmware version, hardware version, and serial number.
Used for updating personal details like email, password, and preferences.
Accesses data transmitted from the spa, such as Spa Boy power consumption.
How to log out of the My Arctic Spa system using the logout button.
Recommends obtaining technical data from retailers or the Arctic Spas website.
Identifies significant changes made to the manual through revisions.
Defines Spa Boy as an advanced salt water maintenance system.
Details what Spa Boy does, including data logging, sanitizer production, and water softening.
Lists advantages like automatic sanitizer maintenance, reduced chemical use, and time savings.
Explains the operational flow of Spa Boy, from consumer registration to data logging.
Illustrates the system's interface connecting the spa, generator, probe, and server.
Depicts and names the key components of the Spa Boy system, such as Eco PAK and generator.
Provides a summary of Spa Boy version releases and their features.
Tracks release dates and summaries for different Spa Boy versions.
Table for owners to record their spa's installed Spa Boy version details.
Explains how to find the spa's production date using the serial number.
Defines terms related to Spa Boy, including Spa Boy, Output Electrode, Sensor, and Communication Cable.
Defines Calcium Hardness (CH) and its implications for spa water.
Defines Total Alkalinity (TA) and Potential Hydrogen (pH) and their roles in water balance.
Defines Chlorine (FCL), Sanitizer, and ORP in the context of the Spa Boy system.
Lists water chemistry abbreviations (CH, TA, pH, FCL, ORP) and their target ranges.
Refers readers to the main Owners Manual for Spa Boy warranty details.
Provides a visual flowchart of the Spa Boy start-up process.
Guidance on filling the spa with water, including optional pre-filter use.
Instructions for connecting power to the spa after filling.
How to set the desired water temperature on the topside controller.
Explains how to adjust filtration settings via OnSpa or the topside controller.
Instructions for stabilizing spa water temperature before balancing chemicals.
Guides on testing and adjusting Total Alkalinity for proper spa water balance.
Instructions for testing and adjusting pH levels to the recommended range.
Details on dissolving salt crystals for the Spa Boy system.
How to add dissolved salt and re-test water chemistry.
Instructions to repeat salt addition and testing steps until target levels are met.
Guidance on testing sodium chloride levels using salt test strips.
Detailed steps for accurately using sodium chloride test strips.
Table showing required salt dosage for different spa models and estimated impact.
Guidance on establishing and maintaining sanitizer (ORP/Chlorine) and pH readings.
Step-by-step instructions for replacing the Spa Boy Output Electrode.
Important care instructions for the Spa Boy sensor to prevent damage.
Procedures for protecting the sensor housing when draining spa water.
Explains how adding salt affects pH and the target range.
Troubleshooting steps for low ORP readings, including checking dashboard and settings.
Guidance on when and how to add Arctic Pure Boost or other sanitizers.
Instructions for adding Arctic Pure Refresh to the spa water.
How to maintain pH to prevent impedance issues with the electrode.
Addresses sudden changes in water color (yellow, green, rusty) and potential causes.
Steps to diagnose and resolve cloudy spa water issues.
Advice on using scale removers and maintaining calcium levels.
Explains how high phosphate levels affect sanitizer output.
Addresses whether softened water can be used with the Spa Boy system.
Recommends performing a system flush before refilling spa water.
How to manually activate the Spa Boy system for increased sanitizer output.
Outlines the typical water maintenance program for Spa Boy V1 R1, including frequency and tasks.
Provides guidance on adjusting pH, ORP, Sodium Chloride, and filter/water changes.
Flowchart to troubleshoot low ORP readings, starting with checking the electrode and generator.
Continues the flowchart for low ORP readings, checking salinity and battery life.
Recommends obtaining technical data from retailers or the Arctic Spas website.
Summarizes revisions for Onzen Version 8 and Eco-Pak controller.
Defines Onzen as a natural salt-water softening and maintenance system.
Details Onzen functions like water softening, clarifying, and automatic sanitizer addition.
Lists advantages of Onzen, including softer skin, cleaner water, and reduced chemical use.
Explains Onzen operation involving salt blend and automatic sanitizer production.
Explains how to find the spa's production date using the serial number.
Defines terms related to Onzen, including Output Electrode and Version.
Defines Calcium Hardness (CH) and its impact on spa water.
Defines TA and pH, their importance, and adjustment methods for Onzen.
Defines Chlorine (FCL), Sanitizer, and ORP in the context of the Onzen system.
Lists water chemistry abbreviations (CH, TA, pH, FCL, ORP) and their target ranges.
Explains abbreviations for Filter Cycle Duration (Fd) and Frequency (FF).
Details how to set Onzen cycle duration for chlorine production.
Explains ozone cycle duration settings for spas equipped with ozone.
Provides a flowchart for the Onzen system start-up process.
Steps for filling the spa, powering it up, and setting the water temperature.
Guides on testing and adjusting calcium and total alkalinity for Onzen.
Instructions for testing and adjusting pH for the Onzen system.
Details on mixing salt crystals for the Onzen system.
How to add salt and re-test water chemistry for Onzen.
Instructions to repeat salt addition and testing steps for Onzen.
Guidance on testing sodium chloride levels for the Onzen system.
Table showing required salt quantities for different spa models for Onzen.
Steps to correctly use sodium chloride test strips for Onzen system.
Instructions for stabilizing spa water temperature after programming settings.
Explains filter cycle suspension when accessories are used manually.
Guides on programming filtration options and Onzen system settings.
How to access filtration options via the topside controller.
Setting the ozone cycle duration through the topside controller.
Setting up Onzen system parameters and cycle duration.
Setting the filter duration in hours via the topside controller.
Setting the filter cycle frequency per day via the topside controller.
Test to confirm if the Onzen system is producing sanitizer by checking gas bubbles.
Information on software revision display and the pack's purge cycle.
Verifying the Onzen output electrode releases fine mist bubbles.
Instructions on allowing the Onzen system to produce sanitizer and what to do if bubbles are not visible.
Steps to reset filter cycle duration and desired temperature after testing.
Guidance on establishing and maintaining sanitizer (Chlorine) readings and levels.
Flowchart to diagnose and resolve cloudy water issues in the Onzen system.
How to perform a "Sanitizer Production test" to check if Onzen is working.
Steps to take if the "Sanitizer Production test" fails.
Solutions for high chlorine levels, including adjusting Onzen output or using neutralizers.
How to manage continuously increasing pH levels with Onzen systems.
Addresses concerns about salted water potentially damaging lawns.
Explains causes and solutions for bright yellow, green, or rusty water colors.
Outlines typical weekly, monthly, and semi-annual maintenance tasks for Onzen.
Addresses phosphate impact and cloudy water troubleshooting for Onzen.
Discusses using softened water with the Onzen system.
Recommends performing a system flush before refilling spa water.
Important notice regarding Onzen V8 salt cell replacement and handling.
Table outlining typical water maintenance for spas fitted with Onzen.
Details how to adjust TA, pH, FCL, CH, Sodium Chloride, and Onzen output.
Lists specifications for Bear Essentials Class models: dimensions, heater, capacity, weight, and electrical.
Diagram showing the layout and connections of the in.ye control pack.
Provides detailed dimensional drawings for the in.ye control pack.
Instructions for installing the keypad, including routing the cable.
Steps for connecting the main keypad to the spa pack.
Wiring diagrams for North American models, emphasizing GFCI panel and terminal blocks.
Wiring diagrams for in.ye European models, covering single and three-phase connections.
Details specifications for the heat.wav heater, including voltage and flow rate.
Guides on connecting heater wires for 240V and 120V North American models.
Instructions for power-up sequence, breaker settings, and checking for proper operation.
Explains the dry-fire protection feature and its operation during power flow checks.
Describes the sequence of displays shown on the keypad during boot-up.
How to select low-level menu options and configure breaker settings.
Information on connecting high voltage accessories like AMP pins and housings.
Tables detailing UL and CE configuration for in.ye PCB, showing slot assignments.
Provides an overview of the spa's main functions and operations accessible via the digital keypad.
How to put the spa into Off Mode and the display behavior.
Instructions for operating Pump 1 at low and high speeds.
Instructions for operating Pump 2.
How to turn the spa light on and off.
How to use the Up/Down keys to adjust temperature and select menu options.
How to navigate the program menu to set time, temperature, and other options.
Step-by-step guide to setting the spa's clock.
How to set filter duration and cycle frequency.
Setting the frequency of filter cycles within a 24-hour period.
How to set the duration for ozone cycles.
How to set economy mode duration for filtration.
How to switch between Fahrenheit and Celsius temperature units.
Explains the Smart Winter Mode for protecting the system from cold.
Information on cooldown procedures after performing tasks.
Step-by-step guide for resolving the Hr internal hardware error.
Flowchart and steps to resolve the Prr temperature probe issue.
Flowchart and steps to resolve HL high temperature error.
Further steps for resolving HL error, including checking probes and heater.
How to shorten filter cycle duration based on weather conditions.
Flowchart and steps to diagnose and fix FLO (no water flow) errors.
Flowchart and steps to resolve OH (high water temperature) errors.
Troubleshooting steps for UPL (no low-level configuration software) errors.
Flowchart and step-by-step guide to troubleshoot Pump 1 not working.
How to check voltage readings for Pump 1 operation.
Flowchart and steps to troubleshoot Pump 2 or blower not working.
How to check voltage readings for Pump 2 operation.
Flowchart and steps to troubleshoot the ozonator not working.
Troubleshooting guide for when the entire system appears unresponsive.
Voltage checks for North American systems when nothing seems to work.
Voltage checks for European systems when nothing seems to work.
Verifying keypad and transformer fuse connections when the system is unresponsive.
Flowchart and steps to diagnose and resolve spa heating issues.
Troubleshooting steps for a keypad that does not seem to work.
Explains why GFCI trips occur and how to troubleshoot them.
Step-by-step guide for setting the clock, filtration cycles, and essentials salt.
How to set the filter frequency and continue to other settings.
How to set the time duration for the salt system.
How to set the desired temperature and save settings.
Guide to setting low-level programming parameters for the INYE pack.
Electrical specs for Model Y series, including input rating and heat.wav rating.
Electrical specs for Model Y Series TUV, including voltage and flow rate.
Details warranty for spa shell, equipment, and plumbing.
Covers warranty for various components, shell surface, and covers.
Warranty for essential sound stereo and essential salt systems.
Warranty for Forever Floor and limited warranty for self-contained spas.
Specific warranty information for spa pumps, including shaft seal coverage.
Details warranty service, conditions, and exclusions for customer responsibility.
Lists conditions voiding the warranty, including alterations, misuse, and improper installation.
Disclaimers on liability, costs, and statement of all provided warranties.
To Next Page