EasyManua.ls Logo

Arduino MLT-BT05 User Manual

Arduino MLT-BT05
5 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background image
6. set/query broadcast interval:
instruction response parameter
AT+ADVI<Param> +ADVI=<Param>
OK
Param :( 0-6
0 ——100ms
1 ——500ms
2 ——7500ms
3 ——1000ms
4 ——2000ms
5 ——4000ms
6 ——8000ms
default 0
AT+ADVI +ADVI=<Param>
7. set/query module authentication job type:
instruction response parameter
AT+TYPE<Param> +TYPE=<Param>
OK
Param ( 0-2 )
0——no password
1——password pairing
2——password pairing
and binding
default 0
AT+TYPE +TYPE=<Param>
8. set/query- serial baud rate:
instruction response parameter
AT+BAUD<Param> +BAUD=<Param>
OK
Param ( 0-4 )
Values (decimal):
0 ——115200
1 ——57600
2 ——38400
3 ——19200
4 —— 9600
default 0
AT+BAUD +BAUD=<Param>
9. set/query-Service UUID
instruction response parameter
AT+UUID<Param> +UUID=<Param>
OK
Param: 0x0001~0xFFFE
default 0xFFE0
AT+UUID +UUID=<Param>
10. set/query-Characteristic
instruction response parameter
AT+CHAR<Param> +CHAR=<Param>
OK
Param:0x0001~0xFFFE
default 0xFFE1
AT+CHAR +CHAR=<Param>
Question and Answer IconNeed help?

Do you have a question about the Arduino MLT-BT05 and is the answer not in the manual?

Arduino MLT-BT05 Specifications

General IconGeneral
BrandArduino
ModelMLT-BT05
CategoryControl Unit
LanguageEnglish

Summary

AT Directive

set/query master/slave mode

Configure and retrieve the module's master or slave operating mode (0-4).

get software version number

Retrieve the firmware version of the Bluetooth module.

get module Bluetooth address

Obtain the unique MAC address of the Bluetooth module.

set/query device name

Set or retrieve the broadcast name of the Bluetooth module (max 18 bytes).

set/query match code

Configure and query the pairing password for the module (6 bytes).

set/query broadcast interval

Adjust the time interval for broadcasting advertising data (0-6, 100ms-8000ms).

set/query module authentication job type

Define the module's authentication method (0-2: no password, pairing, binding).

set/query serial baud rate

Configure and retrieve the serial communication baud rate (0-4: 115200-9600bps).

set/query-Service UUID

Set or query the Service Universally Unique Identifier (UUID) (0x0001-0xFFFE).

set/query-Characteristic

Set or query the Characteristic Universally Unique Identifier (UUID) (0x0001-0xFFFE).

set/query-iBeacon UUID

Configure and retrieve the UUID for iBeacon advertising.

set/query-iBeacon Major

Set or query the Major value for iBeacon advertising (0x0001-0xFFFE).

set/query-iBeacon Minor

Set or query the Minor value for iBeacon advertising (0x0001-0xFFFE).

software restart (reboot after 500mS)

Initiate a software restart of the module with a 500ms delay.

enter low power mode

Command the module to enter a low power consumption state.

search for Bluetooth devices

Start or stop scanning for nearby Bluetooth devices (master mode).

connect the remote device

Establish a connection with a remote Bluetooth device (master mode).

get host scan to slave MAC address

Retrieve MAC addresses of scanned slave devices (master mode).

bind device

Bind a device to the module, often for persistent connections (master mode).

unbind

Remove a previously bound device from the module (main mode).

get the number of slaves to be scanned

Query the count of discovered slave devices (main mode).

disconnect

Disconnect from a connected device (main mode command).

disconnet (master mode command)

Check the connection status of a device (master mode).

set/query -micro letter H5 factory server communication

Configure communication for micro letter H5 factory server (0-1).

Related product manuals