How to fix an inoperative electric starter on an Argo Utility Vehicle?
If the electric starter on your Argo Utility Vehicle is inoperative, begin by cleaning and re-tightening all electrical connections to address potential looseness. If that doesn't work, check the battery charge; recharge it or replace the battery if needed. If the problem persists, the starter motor may be faulty, requiring service by an Argo dealer.
How to fix an inoperative electric starter on Argo Utility Vehicle?
If the electric starter on your Argo Utility Vehicle is inoperative, start by checking for loose electrical connections and clean and re-tighten them. If that's not the issue, the battery charge may be low or dead, so recharge or replace the battery as necessary. If the problem persists, the starter motor may be faulty, requiring service from an Argo dealer.
What to do if Argo Utility Vehicle will not move or turn?
If your Argo Utility Vehicle won't move or turn, first ensure the transmission is properly engaged in gear and not in neutral. Check the drive belt for excessive wear and replace it if needed. Other potential causes include a clutch not engaging, transmission failure, brakes not functioning (adjust caliper or replace brake pads), a broken idler chain (repair or replace), or a broken idler sprocket weld (have vehicle serviced by an Argo dealer).
How to repair air leaking from Argo Utility Vehicle tire?
If your Argo Utility Vehicle tire is leaking air, it might be punctured. Remove the tire from the rim and repair the hole with a radial tire patch or install a tube. If the tire isn't properly seated on the bead, deflate it, carefully push the tire bead off the rim, clean the rim bead area, and re-inflate. If the leak's position isn't obvious, submerge the tire and rim in water to check for leaks through the rim halves or valve stem. Repair as needed. A defective valve may also be the cause, so replace it if necessary.
Why does my Argo Conquest Utility Vehicle pull to the right?
If your Argo Utility Vehicle pulls to the right, check the tire pressure. If the right tire pressure is too low or the left tire pressure is too high, inflate all tires to the correct pressure. Also, ensure the steering lever is held forward against the dash and adjust the brake assembly if required. A broken right side drive chain could also be the cause; repair or replace it.
Why is there severe vibration when operating my Argo Conquest Utility Vehicle?
If your Argo Utility Vehicle experiences severe vibration during operation, several issues could be the cause. The engine might be loose on its mounts, requiring service from an Argo dealer. Other potential problems include a defective driver or driven clutch or engine (also requiring dealer service), a bent axle (remove and straighten or replace), a bent wheel rim (replace), or a worn or damaged drive belt (replace; clutch service may be required).
Why are the hydraulic brakes spongy on my Argo Conquest Utility Vehicle?
If the hydraulic brakes on your Argo Utility Vehicle feel spongy or there's excessive steering lever travel, it could be due to air in the hydraulic system. In this case, have an Argo dealer bleed the brake system and add fluid. A leak in the system could also be the cause, so have a dealer check all fittings, hoses, calipers, and seals for loose connections or leakage and refill as needed. Also, check for loose brakes and adjust or tighten them.
Where is water leaking into the lower body of my Argo Conquest?
If water leaks into the lower body of your Argo Utility Vehicle, it could be due to several reasons. A leak might have developed at the axle bearing flange, in which case you should replace the bearing flange gaskets. Alternatively, the bearing flange seal may be damaged and require replacement. If water is leaking around the outer bearing flange bolts, caulk under the 103-81 bolt heads with silicone sealer. Other potential causes include a cut or punctured lower body (repair or replace), or drain plugs not in place (secure drain plugs).
What causes a loud bang when turning my Argo Conquest Utility Vehicle?
If you hear a loud bang when turning your Argo Utility Vehicle right or left, it could be due to worn or loose idler chains, or worn or loose drive chains. Adjust or replace the idler chains or drive chains as required.
Why are the brakes ineffective on my Argo Conquest?
If the brakes on your Argo Utility Vehicle are ineffective, the pads may have overheated and glazed, or they might be contaminated with lubricant. In either case, have the pads cleaned by an Argo dealer or replace them. Also, if the pads are worn beyond 0.10", replace them.
General| Brand | Argo |
|---|---|
| Model | Conquest |
| Category | Utility Vehicle |
| Language | English |
Describes vehicle's capability and safety for water travel.
Details vehicle identification numbers and model prefixes.
Illustrates and labels controls for different Argo models.
Explains operating hazards indicated on vehicle labels.
Guidelines for initial vehicle operation and maintenance.
Daily checks to ensure vehicle readiness and safety before operation.
Instructions on proper fueling procedures and gasoline types.
Explains how to operate brakes and steering levers/handlebar.
Step-by-step guide for starting the engine using the electric start system.
Details operation of the four-position transmission gears.
Instructions for maintaining straight travel using steering controls.
Explains skid-steer turning mechanics and precautions.
Lists essential items and precautions for traveling in remote areas.
Safety precautions and procedures for operating in water.
Precautions for operating the vehicle in winter conditions.
Details engine oil checking, recommendations, and changing procedures.
Outlines components requiring lubrication and intervals.
Covers battery, fuses, and spark plugs maintenance.
Maintenance procedures for drive belts, chains, and tires.
Inspection and adjustment of mechanical brake system.
Maintenance for hydraulic brake fluid, pads, and adjustments.
Lists common malfunctions, probable causes, and corrective actions.
Procedures for washing and cleaning the vehicle body.
Steps for preparing the vehicle for extended storage.
Identifies potential hazards and provides methods to avoid them.
Information on installing and operating Argo track systems.
Safe operation rules and tips for extending the life of the power winch.
Details ROPS benefits, hazards, and installation notes.
Instructions for modifying Vice Grips for chain work.
To Next Page
