Argo GREENSTYLE 9000 UI

Questions and Answers

J
Julie SuttonAug 16, 2025
How to fix Argo GREENSTYLE 9000 UI air conditioner that does not work?
- R
  Robert PerezAug 16, 2025
  If your Argo Inverter air conditioner isn't working, it might be due to a power outage. In this case, wait until the power is restored. Also, check if the power plug is securely in the socket; if it's loose, plug it in tightly. A blown fuse in the power switch could also be the culprit, so replace the fuse if necessary. Finally, the timer settings may be delaying the start; either wait or cancel the timer.
D
Danny BrownAug 19, 2025
Why is my Argo GREENSTYLE 9000 UI blowing air but not cooling/heating properly?
- J
  Jeffrey MelendezAug 19, 2025
  If your Argo Inverter is blowing air but the cooling or heating isn't effective, the filter may be excessively dusty. Clean the filter, remove any obstacles from the air inlet and outlet, and adjust the louver blades. Also, ensure doors and windows are closed to prevent poor cooling or heating. Make sure the mode setting is correct, and the temperature and wind speed are appropriately set.
A
afosterAug 22, 2025
Why is my Argo Inverter making abnormal sounds?
- R
  richardmaxwellAug 22, 2025
  If your Argo Inverter unit makes abnormal sounds, it could be the fan or compressor relay switching on or off, which is normal. However, excessive dust on the air filter might cause fluctuating sounds, so clean the air filters promptly. If 'Strong wind' is activated and causing too much noise, deactivate the function if it's uncomfortable.
J
Jordan DavidsonAug 26, 2025
Why does my Argo Inverter smell?
- L
  Lisa JohnsonAug 26, 2025
  If your Argo Inverter is emitting an odor, it may be due to an accumulation of odors in the environment. To resolve this, clean the air filter or activate the cleaning function.
G
Gregory CainAug 28, 2025
What to do if there are water drops over the surface of Argo GREENSTYLE 9000 UI Inverter?
- L
  lisa29Aug 28, 2025
  If you notice water drops on the surface of your Argo Inverter indoor unit, it is likely due to high ambient humidity, which is a normal physical phenomenon. Also, prolonged cooling in an open space can cause water drops, so close the doors and windows. Lastly, ensure the louver blades are sufficiently open to prevent water drops at the air inlet.
T
Tina ParkerAug 31, 2025
What to do if Argo Inverter can't run after immediate start-up after shutdown?
- A
  allison30Aug 31, 2025
  If your Argo Inverter doesn't run immediately after being shut down, the protective delay switch is likely delaying operation for 3 to 5 minutes. This is normal.
C
christopher72Sep 3, 2025
Why does my Argo GREENSTYLE 9000 UI Inverter stop running after starting?
- D
  Danielle RiveraSep 3, 2025
  If your Argo Inverter stops running after starting up for a while, it may have reached the set temperature, which is a normal function. Alternatively, it might be in a defrosting state and will automatically resume running after defrosting. Lastly, a shutdown timer may be set; if you wish to continue using it, turn it on again.
P
Patrick CombsSep 6, 2025
Why does Argo Inverter blow out mist during cooling?
- M
  Manuel BrownSep 6, 2025
  The mist coming from the Argo Inverter unit during cooling is because the indoor air is cooled rapidly when the indoor temperature and humidity are high. This is normal.
D
Douglas BennettSep 9, 2025
What is the running water sound from my Argo GREENSTYLE 9000 UI Inverter?
- R
  rhonda43Sep 9, 2025
  The sound of running water you hear during the operation of your Argo Inverter is the sound of the refrigerant flowing, and it is not a malfunction.
D
David GuerreroSep 12, 2025
Why does my Argo GREENSTYLE 9000 UI make a clicking sound when starting or stopping?
- M
  Michael HaneySep 12, 2025
  The slight 'click' sound you hear at the start-up or shut-down of your Argo Inverter is due to temperature changes. This is normal and not a fault.