This document is a user manual for the Ariel AM128 Whirlpool Bathtub, a C-Series model with Bluetooth functionality. It provides comprehensive instructions for installation, operation, and maintenance of the bathtub.
Function Description
The Ariel AM128 is a whirlpool bathtub designed for relaxation and therapeutic use. It features a computerized control system that manages various functions, including water jets, underwater lighting, and a music system with both FM radio and Bluetooth capabilities. The system is designed to operate safely with built-in water-level sensors and a 2-hour automatic shut-off timer.
Important Technical Specifications
- Electrical Operational Parameters:
- Rated Voltage: AC110V~120V
- Rated Current: 10.2A
- Recommended Power Service: GFCI-Protected 15A
- Rated Frequency: 60HZ
- Rated Power: 1125W
- Waterproof Level: IPX5
- Insulating Resistance: >20M
- Component Parameters:
- Water Pump:
- Rated Load Voltage: AC110V~120V
- Rated Load Frequency: 60HZ
- Rated Load Power: 990W
- Lighting:
- Rated Load Voltage: AC12V
- Rated Load Power: 7W
- Speaker:
- Water Pressure:
- Maximum Inlet Water Pressure: 0.5 mPa (5 bars / 72.5 psi)
- Minimum Inlet Water Pressure: 0.1 mPa (1 bar / 14.5 psi)
- Maximum Hot Water Temperature: 80°C (176°F)
- Drain Hose Size (Optional): 40mm (1.5-inches)
- Water Inlet Connections (Optional): 1/2-inch National Pipe Thread (NPT/FIP/MIP)
- Electrical Connection: Must be connected using a Residual Current Device (RCD) or Ground-Fault Circuit Interrupter (GFCI/GFI).
- Grounding: The motor must be grounded with wire not less than 1.63mm-diameter (14AWG) or as required by local codes.
- Water-Level Sensor: Essential for whirlpool system operation; jets will not run unless fully submerged.
Usage Features
The bathtub's functions are controlled via a display panel with several buttons:
- Power Standby Button: Turns the computerized system on/off. The system remains in "standby" when power is supplied. To activate, press and hold for 3 seconds. The system automatically enters "standby" after 2 hours of activation.
- Water Jet Button: Activates/deactivates the water pump and whirlpool features. It only operates when the water level is above the water-level sensor. The default operating time for water jets is 20 minutes. Press and hold for 2 seconds to stop the feature.
- Color Changing Lights Button: Turns on the underwater lights and cycles through brightness settings (3 levels + OFF).
- Light Brightness Button: Adjusts the intensity or brightness of the tub light feature.
- Parameter Setting Button: Used in conjunction with "UP" and "DOWN" buttons to change function parameters, such as light color (C=1 to C=7) or light brightness (B=1 to B=3).
- Volume/Parameter "UP" & "DOWN" Buttons: Adjusts volume or changes parameter values.
- Music Button: Activates the FM radio or Bluetooth functions. Pressing it cycles between Radio and Bluetooth.
- Channel Memory Button: Used to change user-preset channels on the radio feature.
- Radio Function:
- Volume adjustment from "0" to "19" dB (3 dB default).
- Frequency adjustment.
- Search for new radio channels by pressing and holding "UP" or "DOWN" buttons for 2 seconds.
- Program frequencies into 10 channel memories.
- Bluetooth Function:
- Activated by pressing the Music button to cycle past Radio.
- System name: "Whirlpool".
- Password: "1234".
- Chimes upon successful connection.
- Plays audio output only; does not accept vocal input.
- Automatically pauses music for incoming/outgoing calls.
- Automatically connects to previously paired devices. To scan for a new device or if connecting to an undesired paired device, press and hold the Music button for 3 seconds until the Bluetooth symbol flashes.
- Sound volume can be adjusted using parameter setting buttons (9 levels).
- Air Bubble Regulator Valve: Controls the amount of air bubbles in the Water Jet feature.
- Faucet Operation:
- Selector Valve (Clock-wise): Controls water flow to OFF-position, waterfall faucet, handheld shower wand, or jet-plumbing.
- Temperature Valve: Rotates to adjust water temperature (H for hotter, C for colder).
Maintenance Features
- Drain Cleaning: The drain should be cleaned regularly to prevent clogging from hair or soap scum.
- Chrome Parts: Clean with soft materials; avoid abrasive compounds, harsh chemicals, hard objects, blades, or screwdrivers to prevent damage or scratches.
- Acrylic Surfaces: Clean with a soft sponge and a detergent free of ammonia, acetone, or other harsh chemicals to prevent dulling or damage. Dulled surfaces can be refinished with an acrylic polishing compound.
- Whirlpool System Cleaning:
- Monthly cleaning with a whirlpool cleaning solution from a local hardware store is recommended.
- If black flakes appear in the bath, the system needs repeated cleaning until they disappear.
- Alternatively, a cup of chlorine bleach (sodium hypochlorite) with minimum warm/hot water can be used to activate the whirlpool system between regular cleanings. Thoroughly flush and rinse the bathtub and whirlpool system before use.
- General Warnings:
- Do not use cleaning materials other than those recommended by the manufacturer.
- Any service, adjustment, or repair should only be performed by an experienced and licensed professional.
- Avoid using bath oils in whirlpool bathtubs as residue can stick to surfaces and plumbing.
Need help?
To Next Page
General
