Ariens 921 Series Sno-Thro User Manual (English)

Questions and Answers:

A
Amy CampbellAug 7, 2025
Why won't my Ariens 921 Sno-Thro Snow Blower engine crank/start?
- R
  Ronnie HarrisAug 8, 2025
  If your Ariens Snow Blower engine won't crank or start, there are several possible causes: * The fuel tank may be empty, so fill the fuel tank. * The fuel shut-off valve may be closed, so open the fuel shut-off valve. * There may be a build-up of dirt and residue around the governor/carburetor, so clean the area around the governor/carburetor. * The key switch may not be in the run position, so put the key switch into the run position. * The electric starter may not be functioning, so check for a bad starter or connections.
B
Bryce WilliamsAug 13, 2025
What to do if my Ariens Snow Blower throws snow poorly?
- B
  Becky TurnerAug 13, 2025
  If your Ariens Snow Blower unit throws snow poorly or not at all, consider the following potential causes: * Shear bolts may be broken, so replace the shear bolts. * The attachment clutch/brake may not be adjusted properly, so adjust the attachment clutch/brake. * The impeller may be frozen in place, so move the unit to a warm place to thaw it. * Ice or debris may be obstructing the auger, so with the engine off and the auger disengaged, check for obstructions and remove them. * Attachment drive belts may be slipping, worn, or damaged; adjust or replace the belts.
K
Kimberly HarperAug 20, 2025
Why does my Ariens 921 Sno-Thro engine keep stopping?
- R
  Robert PatrickAug 20, 2025
  If your Ariens Snow Blower engine stops, the possible causes are: * The unit is out of fuel, so fill the fuel tank. * The fuel shut-off valve is closed, so open the fuel shut-off valve. * There is a mechanical jam in the blower rake or impeller, so turn off the engine, remove the key, wait for all moving parts to stop, check for and remove any obstruction, and repair before restarting. * The fuel supply is polluted, so replace it with clean fuel. * The spark plug is faulty, so replace or clean the spark plug. * The fuel cap vent is plugged, so replace the fuel cap.
S
Sara LucasAug 26, 2025
Why does my Ariens Snow Blower not operate in Forward / Reverse?
- C
  cheryljohnsonAug 26, 2025
  If your Ariens Snow Blower does not operate in forward or reverse, it could be due to: * A worn-out friction disc, which needs repair or replacement. * A traction belt that is not functioning, requiring repair or replacement. * A speed selector that is not adjusted properly; in this case, adjust the speed selector.
B
Blake CantrellSep 1, 2025
Why do small rubber beads collect in the frame of my Ariens 921 Sno-Thro Snow Blower?
- B
  Brittany LawrenceSep 1, 2025
  Small rubber beads collecting in the frame of your Ariens Snow Blower typically indicate normal friction disc wear. However, chunks or large pieces of rubber mean the friction disc should be checked and replaced if necessary.

Ariens 921 Series Sno-Thro Specifications

General

Brand	Ariens
Model	921 Series Sno-Thro
Category	Snow Blower
Language	English

Summary

Introduction and Model Information

Manuals and Registration

Guides on unit operation, engine service, model/serial numbers, and registration.

Unauthorized Parts and Disclaimers

Unauthorized Replacement Parts Policy

Policy on using genuine Ariens parts to maintain warranty and unit performance.

Product Design Disclaimer

Ariens reserves the right to change product designs and specifications without notice.

Delivery and Assembly Preparation

Customer responsibilities for assembly, safety checks, and product registration.

Safety Guidelines

Safety Notations and Warnings

General reference information and important safety precautions.

Safe Practices and Operator Training

Following safe working precautions and ensuring operator training.

Safety Decals and Locations

Identification and understanding of safety decals on the unit.

Emission Control System

Safety Rules

Assembly

Package Contents

List of all parts included in the Sno-thro unit package for assembly.

Controls and Features

Operation

Dual Handle Interlock System

Ensures safety by interlocking clutch levers during operation.

Traction and Attachment Clutch Operation

How to engage and disengage the left (traction) and right (attachment) clutch levers.

Ignition, Engine Shutoff, and Primer

Proper use of ignition switches, engine shutoff, and primer bulb.

Operation Controls

Speed Selector, Choke, and Throttle Controls

Adjusting speed, choke, and throttle for engine and travel control.

Starting Systems and Tools

Operating electric/recoil starters and using the snow clean-out tool.

Snow Handling Controls

Using the deflector control and chute for snow management.

Operation Adjustments

Chute and Control Adjustments

Operating chute crank, quick-turn control, axle lock pin, and heated handles.

Filling Fuel Tank

Gasoline Guidelines and Safety

Recommended fuel types, octane, safety precautions, and ethanol limits.

Fuel Stabilizer for Storage

Adding fuel stabilizer to extend fuel life for storage.

Fueling Procedure Steps

Detailed steps for safely filling the fuel tank.

Pre-Start Checks

Impeller, Clutch, and Interlock Checks

Verifying impeller, clutches, and dual handle interlock function.

Axle, Skid Shoes, and Fuel/Oil Checks

Checking axle pins, skid shoes, fuel/oil levels, and oil.

Emergency Stop Procedure

Understanding how to stop the unit immediately in an emergency.

Starting and Shut Off

Manual Engine Start Procedure

Step-by-step instructions for manually starting the engine.

Electric Engine Start Procedure

Step-by-step instructions for starting the engine using the electric starter.

Operation During Use

Engine Shut Off and Snow Removal

Steps to shut off the engine and tips for effective snow removal.

Traveling and Transporting Procedures

Guidelines for moving the unit between areas and for transport.

Maintenance

Maintenance Schedule Overview

Recommended service intervals for routine unit maintenance.

Basic Maintenance Checks

Checks for dual handle interlock and ensuring all fasteners are tight.

Maintenance Details

Clutch, Engine Oil, and Tire Checks

Maintaining clutch operation, engine oil levels, and tire pressure.

Auger Gearcase and Lubrication

Checking auger gearcase oil and performing general lubrication.

General Lubrication

Service and Adjustments

Scraper Blade and Skid Shoes

Adjusting scraper blade for wear and skid shoes for ground clearance.

Shear Bolts Replacement Procedure

Steps for replacing shear bolts that protect the auger assembly.

Service Adjustments

Deflector and Chute Control Adjustments

Adjusting remote deflector and chute rotation mechanisms.

Clutch and Selector Adjustments

Speed Selector Adjustment

Adjusting the speed selector for proper forward/reverse travel engagement.

Attachment Clutch/Brake Adjustment

Adjusting the attachment clutch and brake for correct operation.

Belt and Idler Adjustments

Attachment Idler Arm Roller Clearance

Checking and adjusting clearance for the attachment idler arm roller.

Attachment Brake Function Check

Verifying proper brake pad engagement and clearance.

Belt and Clutch Adjustments

Belt Finger Clearance Check

Checking belt finger clearance to prevent belt contact.

Traction Drive Clutch Adjustment

Adjusting the traction drive clutch to compensate for disc wear.

Drive Belt Replacement Procedures

Steps for removing and installing attachment and traction drive belts.

Drive Belt Installation

Installing New Attachment Drive Belts

Guide for correctly installing new attachment drive belts onto pulleys.

Traction Drive Belt Replacement

Procedure for replacing the traction drive belt.

Friction Disc Replacement

Track and Cable Adjustments

Track Tension Adjustment (921023)

Adjusting track tension for straight unit travel (Model 921023).

Height Adjuster Cable Adjustment (921023)

Adjusting height adjuster cable for proper lock finger engagement (Model 921023).

Storage and Parts

Storage Procedures

Guidelines for storing the unit short-term, long-term, and fuel system prep.

Service Parts and Accessories

Lists of available replacement parts and optional accessories.

Troubleshooting

Engine Starting and Running Issues

Diagnosing and resolving problems with engine starting or stopping.

Drive System and Operation Issues

Troubleshooting drive system engagement and operation problems.

Performance and Running Time Issues

Addressing poor snow throwing, brief running times, or collected debris.

Specifications

Limited Warranty

Special Warranty Extensions

Details on extended warranty periods for specific components like gear cases.

Warranty Information

Warranty Exceptions and Customer Responsibilities

Items not covered by warranty, owner duties, and finding a service representative.

Related product manuals

Ariens Sno-Thro 921 Series

48 pages

Ariens 921 Series

42 pages

Ariens Sno-Thro 920 Series

38 pages

Ariens SNO-THRO 924318-ST824

21 pages

Ariens Sno-Thro Pro 28 926038