Ariston 100 L Technical Manual

CHECK function
This function is normally disabled and
can be
OFF).
This function controls
the electrical connections made
compressor, the fan and the 4-ways valve
; the procedure must be done
inside the tank is below 30 °C.
The CHECK
procedure takes about 8 minutes during which the progress symbols
bottom of the display)
flashes on the display.
If at the end of the procedure the result is
"OK", the electrical connections were made
If displayed "KO ", rec
heck the electrical connections
attention to the numbers indicated on the terminals. Check
To stop this procedure press "mode ".
CHARGE function
This function is normally disabled and
can be
OFF).
This function allows to make a refrigerant
gas
The CHARGE procedure lasts for
30 minutes, then it stops
electrical resistance (1200 W) could switch
on
water.
If an error occurs while charge is running, the function shall be
code displayed.
The charge present in the external unit is sufficient for a connection to the internal unit up to 6m
long.
Use an electronic balance to measure the quantity of gas
RESET function
This function can be
enabled via installer menu (P10
The RESET function restores all
the factory default settings:
Parameter
AUTO MODE
BOOST MODE
PRE-SET TEMPERATURE
P1 MAX.
TEMPERATURE SETTABLE WITH THE
P2
MINIMUM SETTABLE TEMPERATURE
P3 MAX.
TEMPERATURE SETTABLE WITH THE HEAT PUMP
P4 GREEN MODE
P5 ANTI-
LEGIONNAIRE’S DISEASE PROTECTION
P6 VOYAGE MODE
P7 DEFROST (active defrost
activation)
P8 HC-HP (off peak
rate operation mode)
P9
TIME_W (no. of accepted hours of powering)
P11
PROGRAM MODE (P1, P2, P1+P2)
PROGRAM P1 TEMPERATURE PRESET
PROGRAM P1 TIME PRESET
PROGRAM P2
TEMPERATURE PRESET
PROGRAM P2 TIME PRESET
28
can be
enabled via installer menu (C1 Parameter
: default =
the electrical connections made
during installation, switching on the
; the procedure must be done
if the water temperature
procedure takes about 8 minutes during which the progress symbols
(triangles in the
flashes on the display.
"OK", the electrical connections were made
properly.
heck the electrical connections
between indoor and external unit paying
attention to the numbers indicated on the terminals. Check
sensors cable.
can be
enabled via installer menu (C2 Parameter
: default =
gas
addition inverting the thermodynamic cycle.
30 minutes, then it stops
automatically. During this time the
on
, so it’s mandatory to use it with the tank full of
If an error occurs while charge is running, the function shall be
paused or stopped and the error
The charge present in the external unit is sufficient for a connection to the internal unit up to 6m
Use an electronic balance to measure the quantity of gas
added by the weight of the gas bottle.
enabled via installer menu (P10
Parameter).
the factory default settings:
TEMPERATURE SETTABLE WITH THE
HEATING ELEMENT
MINIMUM SETTABLE TEMPERATURE
TEMPERATURE SETTABLE WITH THE HEAT PUMP
LEGIONNAIRE’S DISEASE PROTECTION
activation)
rate operation mode)
TIME_W (no. of accepted hours of powering)
PROGRAM MODE (P1, P2, P1+P2)
PROGRAM P1 TEMPERATURE PRESET
TEMPERATURE PRESET
: default =
if the water temperature
: default =
The charge present in the external unit is sufficient for a connection to the internal unit up to 6m
Factory default setting
ACTIVATED
ACTIVATED
55°C
65°C
50°C
55°C
DEACTIVATED
DEACTIVATED
DEACTIVATED
ACTIVATED
DEACTIVATED
8h
DEACTIVATED
55°C
06:00
55°C
18:00

Ariston 100 L Specifications

General

Power Source	Electric
Pressure Rating	8 bar
Capacity	100 L
Type	Storage Water Heater
Thermostat	Adjustable
Temperature Range	Up to 75°C
Insulation	Polyurethane Foam
Warranty	2 years
Dimensions	Varies by model (approx. 913mm x 450mm x 480mm)
Weight	Varies by model (approx. 27 kg)