Arlec PC222 User Manual

4. Press FUNC. button once again and release,
the meter will display max, line power and the
time of max, line power, power factor. Press
and hold FUNC. button for 5 seconds will clear
max, line power display during this state.
5. Press FUNC. button once again and release,
the meter will display current clock and
accumulative power.
6. Press FUNC. button once again and release,
the meter will display total on time and total
electric charge.
7. Press FUNC. button once again and release,
the meter will display total on time of price 1
and total electric charge of price 1.
8. Press FUNC. button once again and release,
the meter will display total on time of price 2
and total electric charge of price 2.
9. Press FUNC. button once again and release,
the meter will come back to display current
time and line voltage. Press and hold FUNC.
button for 5 seconds to clear accumulative
total electric quantity and total electric charge
during display state of total electric charge or
total electric charge of price 1 or total electric
charge of price 2.
10. LCD display----when total electric quantity,
total electric charge overflow, the OVER will
flash at the same time.
SETTING PRICE OF COST/kWh & OVER LOAD
CURRENT
Press and hold FUNC. button for 5 seconds
during display state of voltage or current or
power.
1. Setting price 1:
a. Press SET button once and release, SET
display, the first digital COST/kWh flash, press
UP button to set it.
b. Press SET button once again and release, the
second digital COST/kWh flash, press UP
button to set it.
c. Press SET button once again and release, the
third COST/kWh flash, press UP button to set
it.
d. Press SET button once again and release, the
fourth COST/kWh flash, press UP button to set
it.
e. Press SET button once again and release, the
radix point COST/kWh flash, press UP button
to set it.
f. Press SET button once again and release, the
weekday flash, press UP bottom to set it.
g. Press SET button once again and release,
the hour of ON TIME flash, press UP button to
set it.
h. Press SET button once again and release,
the minute of ON TIME flash, press UP button
to set it.
2. Setting price 2:
Press FUNC button once and release after finish
Setting price 1. Setting price 2, repeat above
steps.
3. Setting OVER LOAD current data:
Press FUNC. button once and release after finish
Setting price 2.
a. Press FUNC button once and release, SET
and AMP display, the first digital MAX. LOAD
flash, press UP button to set it.
b. Press SET button once again and release, the
second digital MAX.LOAD flash, press UP
button to set it.
c. Press SET button once again and release, the
third MAX.LOAD flash, press UP button to set
it.
d. Press SET button once again and release, the
fourth MAX.LOAD flash, press UP button to set
it.
The OVER LOAD WARNING will flash when load
goes over set data. The function button is now
inactive. You must take out the appliance and
set the OVER LOAD data again.
SETTING CURRENT CLOCK
1. Press FUNC button until the CLOCK displays in
LCD. (Clock is located at the bottom right hand
corner of the LCD).
2. Press SET button once, The “WEEK DAY”
will flash at same time, the clock change to SET
mode. You can set the current clock now.
3. Press UP button to set the “WEEK DAY”.
4. Press SET button once again and release. The
“HOUR” will flash. The “WEEK DAY” will stop
flashing and keep display.
5. Press UP button to set the “HOUR”.
6. Press SET button once again and release, the
“MINUTE” will flash. The “HOUR” will stop flash-
ing and keep display.
7. Press UP button to set the “MINUTE”.
8. Press SET button once again and release, the
time will come back to CLOCK display mode.

Arlec PC222 Specifications

General

Brand	Arlec
Model	PC222
Category	Measuring Instruments
Language	English