To Next PageTo Next Page
Need help?Do you have a question about the ARRI ARRIFLEX 16SR3 and is the answer not in the manual?
General| Camera Type | Film Camera |
|---|---|
| Manufacturer | ARRI |
| Model | ARRIFLEX 16SR3 |
| Film Format | 16mm |
| Power Supply | 12V DC |
| Magazine Capacity | 400 ft (120 m) |
| Image Sensor | N/A (Film Camera) |
| Shutter Angle | 180 degrees |
| Frame Rate | 1 to 75 fps |
| Lens Mount | Arri Bayonet Mount |
Details on storing and transporting the camera and its components.
Information on ARRIHEAD and hydro heads suitable for the camera.
Description and mounting of the BP-6 bridge plate for camera mounting.
Details on mounting and operation of the BP-7 bridge plate with 15mm rods.
Instructions for mounting the S-3 shoulder set for hand-held operation.
Details on mounting and adjusting the camera handgrip.
Procedure for replacing main and accessory fuses in the camera.
Description and mounting of the NC 24/1,2 on-board battery.
Details on the NC 24/7 R battery and its connection.
Information on charging the 24V batteries with the NCL 24 R charger.
Description of the double charger for simultaneous battery charging.
Use of the mains unit for studio operation and high power accessories.
Details on the DC/DC converter for 12V accessories and its wiring.
Function and handling of the loop protector to protect film and pressure plate.
Procedure for opening and closing the magazine door.
Description of film cores and their attachment to spindles.
Instructions for cleaning the interior of magazines.
Procedure for cleaning the TC-magazine's recording unit lens.
Step-by-step guide for loading film into the magazine.
Detailed steps for threading film into the feed side of the magazine.
Instructions for placing and securing the film roll onto the core adapter.
Guide for creating the film loop and threading the take-up side.
Description of the kinematic film movement and registration pin for steadiness.
Procedure to check film transport by running the camera slowly.
How to adjust the camera for optimal running noise with different film stocks.
Details on adjusting the mechanically adjustable mirror shutter angles.
Using the manual inching knob to turn the mirror shutter and movement.
Steps to adjust the mirror shutter opening angle using a special key.
How to check the mirror shutter setting using the camera display.
Overview of available fibre optic viewing screens for the camera.
Procedure for changing and cleaning fibre optic viewing screens.
Step-by-step guide for securely attaching a magazine to the camera body.
Instructions for safely removing a magazine from the camera.
List of compatible 16mm and 35mm lenses for the ARRIFLEX 16SR 3.
Details on the PL-mount for secure lens fastening and precise mounting.
Procedure for attaching lenses to the 54mm PL-mount.
Instructions for removing lenses from the 54mm PL-mount.
Using 41mm ARRI bayonet lenses with a PL/bayonet adapter.
Steps to attach the PL/bayonet adapter to the camera.
Procedure for attaching 41mm bayonet mount lenses to the adapter.
Installing the lens support for heavy lenses.
Steps for mounting the support ring and attaching the lens with support.
Description of the viewfinder's 3D swivel, rotation, and image compensation.
LED indicators for asynchronous operation and low voltage in the viewfinder.
Adjusting the friction for the viewfinder arm's 360° positioning.
How to adjust the viewfinder image position and internal friction.
Diopter compensation on the eyepiece and procedures for removal/attachment.
Using the eyecup shutter to prevent light entry and replacement with heated eyecup.
Mounting and dismounting the LWS-2 light-weight support.
Instructions for using the LWS-2 with VARIO-SONNAR lenses.
Mounting and operation of the FF-3 universal follow focus device.
Using the light-weight follow focus device attached to the light-weight support.
Overview of the LCS as a versatile lens control unit.
Features and mounting of the MB-16 production matte box.
Details on the MB-17 4"x4" matte box and its filter stages.
Mounting of LMB-2 and LMB-3 light-weight matte boxes.
Mounting the FE-2 finder extension for comfortable tripod work.
Mounting and function of the heated eyecup to prevent eyepiece misting.
Adjusting the camera for Normal 16 and Super 16 formats.
Checking and altering the lens alignment for correct flange focal distance.
Procedure for changing the fibre optic viewing screen.
Modifying the film gate opening for Normal 16 and Super 16 formats.
Steps to adjust the viewfinder alignment for proper viewing.
Adjusting bridge plates BP-6 and BP-7 for Normal 16/Super 16 format.
Adjusting the lightweight support for format change.
Adjusting the video optic for Normal 16 to Super 16 format change.
Overview of the camera's LCD display and its six modes.
Procedure for selecting and navigating through the camera's display modes.
How to lock the SEL and SET keys to prevent unintentional value changes.
Detailed guide on setting standard and programmable camera speeds.
Starting and stopping the camera, and remote activation methods.
Steps to select and set standard frame speeds.
Procedure for setting programmable speeds before camera operation.
How to adjust programmable speed while the camera is running.
Switching and resetting the total exposed film and take counters.
How to switch the film counter unit between meters and feet.
Introduction to the upcoming display mode descriptions.
Switching between exposure control and ARRIGLOW for lighting.
Checking the mirror shutter setting via the display and lens.
Synchronizing camera operation with a monitor or external unit.
Adjusting camera frame speed for optimal synchronization with a monitor.
Adjusting the phase for current takes and camera starts.
Using the CCU-1 for remote control of camera functions.
Procedure for opening the battery compartment and replacing batteries.
Connecting the camera control unit to the camera and powering it on.
Explanation of the key functions within the camera control unit menus.
Interpreting error readings and acoustic signals on the CCU display.
Accessing camera settings and sub-menus via the CCU main menu.
Setting camera speeds using the CCU, including standard and programmable.
Operating the camera remotely via the CCU's REMOTE menu.
Setting and displaying time code and user bits via the CCU.
Accessing options for length unit and counter display mode.
Switching the film counter between meters and feet.
Switching the film counter between total exposed and take counter.
Synchronizing the camera with external equipment using ESU-1.
Using remote switches to control camera on/off and run status.
Procedures for mounting the video-assist system and changing the beamsplitter.
Steps for attaching the video optic to the video carrying handle.
Connecting the anti-flicker processor and video camera for the video signal.
Adjusting image position and focus of the video optic.
Meaning of the TC symbol displayed on the camera and magazines.
Recording time code when synchronizing with external units like ESU-1.
Procedure for turning TC recording on and off using the MODE and SET keys.
Synchronizing the camera's TC generator with external LTC signals.
Using TC-output to synchronize equipment or as a master clock.
Displaying time code and user bits information on the camera.
Adjusting TC recording intensity based on film material sensitivity.
Function and limitations of the TC buffer for power supply and time code continuity.
Procedure for testing TC recording functionality with a cable connection.
Procedure for replacing damaged magazine drive gears to eliminate noise.
Instructions for dismounting and cleaning the magazine throat assembly.
Replacing the lens in the TC-magazine recording unit due to scatter.
Replacing the glass window for the film end sensor if scratched.
Checking and adjusting flange focal distance after format changes.
How to check the flange focal distance using depth gauges.
Setting the flange focal distance using adjustment shims and PL-mount.
Readjusting viewfinder friction when it decreases.
Adjusting friction on the viewfinder arm's 25° swing.
Procedure for exchanging the entire electronic housing if it fails.
Checklist for verifying camera readiness across various systems.
Daily checks for batteries, film track, sensors, friction, and magazines.
Specifications including image format, magazines, lens mounts, and speeds.
Part numbers for ARRIFLEX 16SR 3 components and accessories.
