Arrow ET501C - Safety Instructions for Tackers; Tacker Safety Warnings; Specific Safety Rules; Layout and Items Supplied

d ) Under abusive
conditions
, liquid may
be ejected
from the battery ; avoid contact . If contact
accidentally occurs , flush with water . If liquid
contacts eyes , seek medical help . Liquid ejected
from the battery may cause irritation or burns .
1.6 SERVICE
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts . This will ensure that the
safety of the power
tool is maintained .
2. SAFETY INSTRUCTIONS FOR TACKERS
2.1 TACKER SAFETY WARNINGS
Always assume that the tool contains fasteners .
Careless handling of the tacker can result in
unexpected firing of fasteners and personal injury .
Do not point the
tool
towards
yourself
or
anyone
nearby . Unexpected triggering will discharge the
fastener
causing
an
injury .
Do not actuate the tool
unless the tool is placed
firmly against the workpiece . If the tool is not in
contact with the workpiece , the fastener may be
deflected away from
your target .
Disconnect
the
tool from the
power source
when
the fastener jams in the tool .
while removing a
jammed fastener , the tacker may be accidentally
activated
if it
is
plugged in
Use caution while removing a jammed fastener .
The mechanism may be under compression and the
fastener may be forcefully discharged while attempting
to free a jammed fastener .
When fastening electrical cables , make sure the
cables are not energized . Hold the tacker only by
insulated gripping surfaces . Use only fasteners
designed for electrical cable installations . Inspect
that the fastener has not damaged the insulation of
the electrical cables . A fastener that damages the
insulation of electric cables can lead to electric shock
and fire
hazards
.
2.2 SPECIFIC SAFETY RULES
1.Hold tool by insulated gripping surfaces when
performing an operation where the tool may
contact hidden wiring or its own cord . Contact
with a " live " wire will also make exposed metal parts
of the tool " live " and can shock
the operator .
2. Know your power tool . Read operator's manual
carefully . Learn its applications and limitations , as
well
as the specific potential
hazards related to this
tool
. Following this rule
may reduce the risk of
electric shock , fire , or serious
injury .
3. Always wear safety glasses with side shields .
Everyday glasses are NOT safety glasses .
Following this rule may reduce the risk of eye injury .
4. Protect your hearing . Wear hearing protection
during extended periods of operation . Following this
rule may reduce the risk of serious personal injury .
5.
Protect your lungs . Wear a face
or dust mask if
the operation is dusty . Following this rule may
reduce the risk
of
serious
personal
injury .
6. Do not abuse
charger cord . Never carry
tool by
6
charger
cord . Never yank
cord to disconnect it from
outlet . Keep charger cord away from heat , oil , sharp
edges , and moving parts . and sharp edges , and
moving
parts .
7.
Do not attempt to alter
the tool . Your Arrow
cordless power tool has a tested cycling time . It is
designed
to perform adequately
at this rate . Any
unauthorized alteration and / or use could result in a
hazardous condition causing serious personal injury .
Unauthorized parts and / or tool modification
automatically
voids
warranty .
8. Use proper charging device . While charging , the
tool should always be supplied via a residual current
device with a rated residual current of 20 mA or less .
3. LAYOUT AND ITEMS SUPPLIED
3.1
Layout
(
Fig . 1 )
1.ON / OFF Switch
3.Trigger
5.Air
vents
7.Staple exit
9.Charger
3.2
Items
supplied
CARTON CONTENTS
•
Cordless
Power
Tool
•
Charger
•
Original safety and
operating instructions
2.Charge port
4.Battery
status
indicator
6.Contact
safety
8.Quick release magazine
1.
Carefully check to see
that all of the above items
are
supplied .
2. Inspect the product carefully to make sure no
breakage or damage occurred during shipping . If
you
find damaged or missing
parts , please contact
us at the first time .
NOTE : Do not discard the shipping carton and
packaging material until you are ready to use your new
cordless power tool . The packaging is made of
recyclable
materials . Properly dispose
of these
materials in
accordance
with local
regulations
.
IMPORTANT ! The equipment and packaging material
are not toys . Do not let children play with plastic bags ,
foils or small parts . These items can be swallowed and
pose
a
suffocation
risk !
4. TECHNICAL DATA
Power
supply :
Battery capacity :
Battery
type :
Weight
:
Charger
for the product
Battery charge voltage :
Battery charge
current
:
Charging
unit
supply voltag ....
Charging
time :
3.6 V DC
2.0 Ah
Lithium - ion
.1.13kg
5 V DC
.1 A
100-240V 50/60 Hz
2
hours