EasyManua.ls Logo

Ashley M9X572 - User Manual

Ashley M9X572
43 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OWNER’S MANUAL
Installation & Operation
M9X432
M9X442/M9X442A
M9X452/M9X452A
M9X532
M9X542/M9X542A
M9X552/M9X552A
M9X5
72
M9X632
M9X642/M9X642A
M9X652/M9X652A
M9X6
72
Serial No.

Table of Contents

Questions and Answers

  • E
    Erin SchmittAug 19, 2025
    Why is my Ashley M9X572 massage motor so noisy?
    • L
      Levi WadeAug 19, 2025
      Excessive noise from the massage motor on your Ashley Power Foundation might be due to several factors. If your bed is on a hard surface floor, place carpet or rubber pieces under each leg. Elevate the head, foot, or neck section briefly to realign the lift mechanisms. Ensure the foundation isn't against a wall or object that could vibrate. If installed on a bed frame, check that the frame isn't vibrating due to the massage motors. Also, verify that the headboard attachment hardware is properly tightened.
  • J
    Jeffery ScottAug 21, 2025
    What to do if no features of my Ashley Indoor Furnishing power foundation activate?
    • M
      Michelle WoodAug 21, 2025
      If no features of your Ashley power foundation are working, the electrical outlet may be defective. First, program the remote control. Then, unplug the power cord, wait 30 seconds, and plug it back in to reset the electronic components. Finally, test the outlet by plugging in another working appliance to ensure the outlet is functional.
  • J
    Joshua BakerAug 23, 2025
    How to fix Ashley M9X572 head or foot section that won't return to flat position?
    • K
      Kelly CastanedaAug 23, 2025
      If the head or foot section of your Ashley Indoor Furnishing elevates but won't return to the flat position, the bed mechanism may be obstructed. Elevate the bed and check for any obstructions, then remove them. Also, the head section might be too close to the wall, or the headboard might be too close to the mattress edge. Verify there's enough distance between the headboard brackets and the mattress, and adjust if needed.
  • K
    kennethgarciaAug 26, 2025
    Why does my Ashley M9X572 Indoor Furnishing lift function have interference?
    • S
      Susan SmithAug 26, 2025
      Minor interference during the head, foot, or neck lift function of your Ashley Indoor Furnishing may be due to radio frequency interference from other transmitting devices. Check the batteries in the remote control and replace them with three new AAA batteries if necessary. Ensure you are following the motor's duty cycle (do not operate more than 2 minutes in an 18-minute period). Press the lift buttons squarely and accurately, wait several seconds, and try pressing the appropriate button again.
  • B
    barrrebeccaAug 27, 2025
    How to fix an Ashley M9X572 remote that will not illuminate?
    • S
      Scott GatesAug 28, 2025
      If your Ashley Indoor Furnishing remote will not illuminate, replace the batteries in the remote.
  • T
    Tammy JohnsonAug 29, 2025
    What to do if the Ashley Indoor Furnishing massage motor overheats or stops?
    • J
      Jackie ChanAug 30, 2025
      If the vibration motor overheats, the thermal protection will turn the motor off. Wait 30 minutes, then turn the massage back on. If it doesn't come on, turn it off and report the situation to customer service.
  • S
    Shawn ClarkAug 31, 2025
    What to do if Ashley Indoor Furnishing remote works but doesn't activate the bed?
    • J
      Julie BryanSep 1, 2025
      First, ensure the power cord is properly plugged into a working, grounded electrical outlet. To verify the outlet's functionality, test it by plugging in another appliance that you know works.
  • J
    James JonesSep 3, 2025
    Why won't any features activate on my Ashley M9X572 Indoor Furnishing power foundation?
    • B
      Brandon TylerSep 3, 2025
      Try these steps: program the remote control (refer to the Setting Programmable Positions and Pairing Remote section of this manual for programming procedures), unplug the power cord, wait 30 seconds, and then plug it back in to reset the electronic components. Check the electrical outlet by plugging in another working appliance to ensure it is not defective. Also, verify that the connector on the wired remote control is securely attached to the control box.
  • R
    Rebecca AdamsSep 5, 2025
    How to fix Ashley M9X572 remote that will not illuminate?
    • S
      Susan CohenSep 5, 2025
      Replace the batteries in the remote control with new ones.
  • H
    hchapmanSep 7, 2025
    What to do if Ashley M9X572 head or foot section elevates but won't return to flat position?
    • H
      Heather ThompsonSep 7, 2025
      The bed mechanism might be obstructed. Elevate the bed and check for any obstructions, then remove them. Also, the head section may be too close to the wall, or the headboard may be too close to the edge of the mattress. Ensure there is enough distance between the headboard brackets and mattress; adjust if needed.

Ashley M9X572 Specifications

General IconGeneral
ModelM9X572
ColorGray
BrandAshley
MaterialFabric
StyleModern

Related product manuals