EasyManua.ls Logo

ASROCK B150 Pro4/3.1 User Manual

ASROCK B150 Pro4/3.1
139 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Version 1.0
Published October 2015
Copyright©2015 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate
ASRock Website: http://www.asrock.com
Question and Answer IconNeed help?

Do you have a question about the ASROCK B150 Pro4/3.1 and is the answer not in the manual?

ASROCK B150 Pro4/3.1 Specifications

General IconGeneral
Form FactorATX
SocketLGA 1151
ChipsetIntel B150
Memory Slots4
Memory TypeDDR4
Maximum Memory64 GB
PCI Express x16 Slots2
SATA 6Gb/s Ports6
M.2 Slots1
USB 3.1 Gen2 Ports1
Audio7.1 CH HD Audio
PCI Express x1 Slots3
LANGigabit Ethernet
RAID SupportRAID 0, 1, 5, 10
Multi-GPU SupportAMD Quad CrossFireX
USB 3.1 Gen1 Ports6 x USB 3.1 Gen1 (2 Front, 4 Rear)
USB 2.0 Ports6 x USB 2.0 (2 Front, 4 Rear)

Summary

Chapter 1 Introduction

1.1 Package Contents

Lists the items included in the motherboard package.

1.2 Specifications

Details the technical specifications of the motherboard, including CPU, memory, and expansion slots.

Chapter 2 Installation

Pre-installation Precautions

Important precautions to take before installing motherboard components or changing settings.

2.1 Installing the CPU

Step-by-step guide on how to safely install the CPU onto the motherboard socket.

2.2 Installing the CPU Fan and Heatsink

Instructions for attaching the CPU fan and heatsink assembly to the motherboard.

2.3 Installing Memory Modules (DIMM)

Guide on how to correctly install DDR4 memory modules into the DIMM slots.

2.4 Expansion Slots (PCI Express Slots)

Details the motherboard's PCI Express slots and their configurations for expansion cards.

2.5 Jumpers Setup

Explains how to set up jumpers on the motherboard, including the Clear CMOS jumper.

2.6 Onboard Headers and Connectors

Describes various onboard headers and connectors, such as the system panel header and power connectors.

Creating Windows® 7 Installation Disk with USB 3.0 Drivers Packed

Requirements

Lists the necessary software and hardware for creating a Windows 7 installation disk with USB 3.0 drivers.

Instructions

Provides step-by-step instructions for preparing the installation media.

Contact Information

Related product manuals