To Next PageTo Next PageWhat causes piping temperature too high protection in cooling mode on my Astralpool Elyo Smart NN?
Piping temperature too high protection under cooling mode in your Astralpool Heat Pump can be caused by high ambient or water temperature, or an abnormal refrigeration system. First, check the scope of using. Second, check refrigeration system.
Why does my Astralpool Elyo Smart NN have a compressor start failure?
A compressor start failure on your Astralpool Heat Pump can occur due to several reasons: a damaged main board, compressor wiring errors, liquid accumulation inside, or incorrect phase connection. To troubleshoot: First, check the main board. Second, check the compressor wiring according to the circuit diagram. Finally, inspect the compressor itself or replace it.
What causes a communication failure between the controller and main board on my Astralpool Elyo Smart NN Heat Pump?
A communication failure between the controller and main board on your Astralpool Heat Pump can stem from a poor signal wire connection or a controller malfunction. To fix this: First, check and reconnect the signal wire, or replace it. Second, turn off the electricity supply and restart the machine, or replace the controller.
How to resolve a controller failure on my Astralpool Heat Pump?
To resolve a controller failure on your Astralpool Heat Pump, check and reconnect the signal wire, or change it for a new one. Alternatively, turn off the electricity supply and restart the machine, or replace the controller.
What causes overheating protection for water temperature in heating mode on my Astralpool Elyo Smart NN Heat Pump?
Overheating protection for water temperature (T2) in heating mode on your Astralpool Heat Pump can be triggered by low water flow, a stuck water flow switch, or a faulty T2 sensor. To resolve this: First, check the waterway system. Second, check the water pump or water flow switch. Third, check the T2 sensor or replace it.
What should I do if my Astralpool Elyo Smart NN shows an input current over high protection?
If your Astralpool Heat Pump is showing an input current over high protection, it could be due to a large compressor current, abnormal water flow, power fluctuations, or an incorrect PFC inductor. Here's what you can do: First, check the compressor. Second, check the waterway system. Third, ensure the power is within the normal range. Fourth, verify that the correct PFC inductor is being used.
How do I troubleshoot T6 exhaust too high protection on my Astralpool Elyo Smart NN Heat Pump?
If your Astralpool Heat Pump displays a T6 exhaust too high protection error, it could be due to a lack of gas, low water flow, a blocked piping system, or a faulty exhaust temperature sensor. Here’s how to address it: First, check the high pressure gauge; if it's too low, add gas. Second, inspect the waterway system and water pump. Third, examine the piping system for blockages. Fourth, replace the exhaust temperature sensor.
What causes a low pressure failure in my Astralpool Elyo Smart NN Heat Pump?
A low pressure failure in your Astralpool Heat Pump can be caused by a blocked EEV or jammed pipe system, abnormal motor speed or motor damage, or gas leakage. To resolve this: First, check the EEV and piping system, and check the motor. Second, use a high pressure gauge to check the pressure value.
Why is my Astralpool Heat Pump showing a compressor current protection error?
A compressor current protection error on your Astralpool Heat Pump can occur for several reasons: the compressor current is too large, there's a wrong connection for the compressor phase sequence, liquid and oil accumulation in the compressor, damage to the compressor or driver board, abnormal water flow, or power fluctuations. Try these solutions: First, check the compressor itself. Second, inspect the waterway system. Third, ensure the power supply is within the normal range. Fourth, verify the phase sequence connection.
How to fix a water flow failure on my Astralpool Elyo Smart NN?
If your Astralpool Heat Pump is experiencing a water flow failure, it could be due to a damaged water flow switch or insufficient water flow. Try these steps: First, replace the water flow switch. Second, check the water pump and the waterway system to ensure adequate flow.
General| Brand | Astralpool |
|---|---|
| Model | Elyo Smart NN Series |
| Category | Heat Pump |
| Language | English |
