EasyManua.ls Logo

ATA HiRO GDO-12V1AM - User Manual

Default Icon
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
4008033
Conforms to:
ANSI/CAN/UL325
Tested to comply
with Part 15 of the
FCC Rules
Doc # 160417_02
Part # 87515
Released 22/02/21
$ $
% %
& &
' '
( (
) )
* *
+ +
- -
. .
/ /
0 0
1 1
3 3
5 5
7 7






























'5$:1
&+.'
$339'
0)*
4$
81/(6627+(5:,6(63(&,),('
',0(16,216$5(,10,//,0(7(56
685)$&(),1,6+
72/(5$1&(6
/,1($5
$1*8/$5
),1,6+
'(%855$1'
%5($.6+$53
('*(6
1$0(
6,*1$785(
'$7(
0$7(5,$/
'21276&$/('5$:,1*
5(9,6,21
7,7/(
':*12
6&$/(
6+((72)
$
:(,*+7
32:(5'5,9(*'29$<B;;;;;;;;B;;;;;
High Rolling Door Opener
GDO-12
HiR
FOR LIGHT-DUTY COMMERCIAL DOOR USE ONLY
Instruction Manual
(Instruction d’Installation)
MODELS: GDO-12V1AM

Table of Contents

Questions and Answers

  • S
    saracoleAug 13, 2025
    Why does my ATA HiRO GDO-12V1AM reverse for no reason?
    • C
      christian16Aug 13, 2025
      If your ATA Garage Door Opener door reverses for no apparent reason, it may be due to environmental conditions such as wind, dust, or extreme temperature changes. In this case, put the door into manual (Section 5, take note of the CAUTION) and contact (800) 934 9892. Alternatively, if you have Safety Beams installed, ensure that their path is not obstructed. If the issue continues, contact your optional extras dealer.
  • J
    Jacob MoodyAug 18, 2025
    What to do if the Close (Blue) LED is flashing on my ATA HiRO GDO-12V1AM?
    • B
      baileyjamesAug 18, 2025
      If the Close (Blue) LED on your ATA Garage Door Opener continues to flash, it indicates that the door is obstructed when closing. Clear away any obstructions and test the door closes correctly. If the door is damaged, contact your dealer. Also, the limits may be cleared. In this case, remove all power sources, wait until all lights are out (10-15 seconds), then reconnect the power. If the Blue LED is still flashing, the limits are not set. See Section 6 to set the LIMITS.
  • C
    Christine GlassAug 22, 2025
    Why is the ATA HiRO GDO-12V1AM transmitter range so bad?
    • F
      Francis ThompsonAug 23, 2025
      If your ATA Garage Door Opener transmitter range varies or is restricted, keep in mind that variations are normal depending on conditions such as temperature or external interference. See instructions for correct use of transmitter (Section 7.1.1). Also, the battery life may be exhausted. Refer to battery status (Section 7.1.2). Finally, the position of the Remote Control Transmitter in the motor vehicle can affect the range. Try changing its position (Section 7.1).
  • L
    Lori MannAug 27, 2025
    What does it mean if the Open (Green) LED is flashing on my ATA Garage Door Opener?
    • S
      Sierra RobinsonAug 27, 2025
      If the Open (Green) LED on your ATA Garage Door Opener continues to flash, it means the door is obstructed when opening. Clear away any obstructions and test that the door opens correctly. If the door is damaged, contact a door professional.
  • N
    Nathan BlackSep 2, 2025
    What to do if ATA HiRO GDO-12V1AM Garage Door Opener motor runs but door doesn't move?
    • R
      rreyesSep 2, 2025
      If the motor of your ATA Garage Door Opener is running but the door remains stationary, it's possible that the opener is disengaged. To resolve this, re-engage the opener (Section 5).
  • F
    Francis SanchezNov 7, 2025
    How to fix ATA Garage Door Opener when remote control doesn't work?
    • J
      Jeremy CollinsNov 7, 2025
      If your ATA Garage Door Opener doesn't work when using the remote control transmitter, several factors could be at play. First, ensure the garage door itself is in good working order, checking for issues like broken springs. You can refer to the monthly maintenance guidelines in Section 8. Next, confirm that the opener is receiving power by testing the power point with another device. Also, verify that the remote control's battery isn't depleted, replacing it if necessary, as detailed in Section 7.1.2. Check if the opener is in “Vacation Mode” and disable it, if so (Appendix E, Vacation Mode step E.5). Finally, make sure the remote control button is correctly programmed to operate the door, following the coding transmitter procedure in Section 6.7, and ensure you're pressing the correct bu...

Summary

Safety Information

General Safety Instructions

Vital safety instructions for installation and use, covering warnings and cautions.

Electrical Safety Warnings

Precautions regarding electric shock, grounding, and wiring.

Operational Safety Cautions

Operator Safety & Security

Manual Release Procedure

Steps to disengage and re-engage the opener, including safety checks.

Installation Instructions

6.1 Pre-Installation Requirements

6.2 Door Preparation

6.3 Fitting the Opener

6.4 Safety Beam Installation

Installing the infra-red safety beam, including bracket assembly and alignment.

6.5 Setting Speed and Limits

Adjusting door speed, setting travel limits, clearing positions, and re-profiling.

6.6 Safety Testing & Auto-Close

Testing close/open cycles and configuring auto-close functions.

6.7 Coding Transmitters

Procedures for programming remote control transmitters and wall controls.

Operation Instructions

7.1 How to Use Your Operator

User Maintenance Instruction

8.1 Door Maintenance

Troubleshooting

Appendix D - Setting Limits via Transmitter

Appendix E - Additional Transmitter Functions

ATA HiRO GDO-12V1AM Specifications

General IconGeneral
Output Current1A
Motor TypeDC Motor
Remote ControlYes
Safety SensorsYes
Manual ReleaseYes
Installation TypeCeiling Mount
Output Voltage12V
Remote Control Range20 m

Related product manuals