AUDIO MASTER M7 USB - PROFESSIONAL 4;7-channel Mixing Console Instructions; Operating the 1.4;7 Professional Mixer; 4. SPECIFICATIONS; Input Channel Specifications

4. SPECIFICATIONS
INPUT CHANNELS 1 through 5
Mic input
Line input
Frequency response
Gain range
SNR
Frequncy response
Gain range
SNR
STEREO CHANNELS
3 BAND EQUALIZER
MAIN MIX
POWER SUPPLY
Frequency response
Gain range
SNR
LOW
MID
HI
Main Outputs
AUX Send
EFF Send
Tape Out
Phones Output
USA/Canade 120 V~,60 Hz,
U.K./Australia 240 V~,50 Hz,
Europe 230 V~,50 Hz,
Japan 100 V~,50 - 60 Hz,
China 220 V~,50 - 60 Hz,
electronically balanced,discrete input configuration
10 Hz to 200 kHz
+14 dB to +60 dB
120 dB E.I.N.
electronically balanced
10 Hz to 130 kHz
-6 dB to +38 dB
95 dB E.I.N.
10 Hz to 70 kHz
Line: -8 to +15 dB / Mic: +13 to +60 dB
Line: -96 dB / Mic: 104dB E.I.N.
50 Hz, +/- 15 dB
700 Hz, +/- 15 dB
10 kHz, +/- 15 dB
+28 dBu balanced /+22 dBu unbalanced
+22 dBu unbalanced
+22 dBu unbalanced
+22 dBu unbalanced
+15 dBu / 150
Dimensions
Weight
(H X W X D)mm
4channal
7channal
3 0 5 X 2 4 0 X 5 0
4 2 0 X 1 9 5 X 5 0
4channal
7channal
3 . 2 k g
3 . 6 k g
8
PROFESSIONAL 4 / 7 - channel mixing console and Aux paths plus effects processor
4
4/7-channel mixing console with two sereo channels and a separate stereo tape
channel
Separate input JACK controls for mic and line inputs roall mono channels
XLR mic connectors on all mono channels
Low-noise,discrete mic preamplifiers on all microphone inputs
Dedicated inserts on all mono channels
Balanced 1/4 " stero jacks and balance controls on all stereo channels
Separate stereo tape channel with 1/4 " and RCA jacks
Stereo output for recording applications
English musical active 3-babd EQ on all seven channels
AUX and effects paths as well as separate gain controls on all channels
High-grade-sealed faders and potentiometers made by taiwan
Insert option for extemal effects devices
AUX Send and EFF Send controls in the main section for optimal level adjustment
Headphones output with dedicated volime control
Built-in +48V phantom power for condenser mics
Extremely rugged construction ensures long life even under the most demanding conditions
1.4/7 professional mixer instructions
Use this balanced XLR jack to connecta microphone to the machine
(applies to channels 1 through 5)
The phantom power required for condenser mies can be activated with switch .
The INSERT jack allows you to insert, for example,
a compressor or equalizer in the mono channels.
Channels 1 through 5 feature an addditional
LINE input on a balanced 1/4 " jack.
The control determines the channels input gain, both for a microphone
Use the control to adjust the signal s position on the stereo basis.
Your machine c ome s wi th a 3-b and equa liz er, the H Ic ontrol g ove ms
ang e frequen c i es, an d the co n t r ol al l o w s you t o raise o r lower th e gain
of the ba ss range.
Use t he contro l to dete rmi ne the chann el volume sent t o the
mix i s zero .
mix bus. When set fully to the left, the channel volume in the
The fader adjusts the volume of the corres ponding channel
The control adjusts the effects volume for the corresponding channel.
AUX
the high fr equ enc y rang e, t he control can be used to boo st/ cut the midr
connected via the jack and for other signal sources connected to the 1/4 jack.
LOW
MID
PAN
XLR
GAIN MIC
AUXAUX
CHANNEL
EFF
5
6
7
8
9
1
2
3
3
MIC
INSERT LINE
1
?
?
?
17
20
0 60dB
GAIN
HIGH
MID
LOW
PEAK
C H 1
PAN
0
L R
0
-15 +15
0
-15 +15
0
-15 +15
0 10
AUX
EFF
5
0 10
5
+dB
10
5
0
5
10
15
20
25
30
40
60
8
?
?
?
?
?
?