Auto Meter Digital Pro Shift User Manual

C.) PLAYBACK MODE Press and release the MODE (+) .Thedisplaywillindicate“PLaY.”PressENTER to
 conrmyourchoiceandbegin“playingback”therunstoredinthememoryonthedisplayat
1
⁄
3
real time.
To“Rewind”thecurrentrunbeingplayedback,pressandholdtheEXIT (–) button. The display will play the run backward from
 itscurrentpositioninrealtime,foraslongasRewind/Pauseispressed.OnceRewind/Pauseisreleased,playbackwillbe“Paused”.
To resume playback at
1
⁄
3
real time, press and release the MODE (+) button. Pressing and holding the MODE (+) will play the run forward in real time.
 WhentheMODE (+) is released, playback will resume at
1
⁄
3
realtime.DuringPlayback,theTachOutputonthevioletwirewillbeactive.
D.) SHIFT POINT SET –Once“SptS”isshownonyourdisplay,pressENTERtoconrmthatyouwouldliketosetyourshiftpointorpoints.“SP1”willnowbe
displayed. To set your shift point, press ENTERtoconrmtheshiftpointyouwouldliketoset.Thedisplaywillnowshowyouthecurrentshiftpointsetting.
 UsetheMODE (+) and EXIT (–) buttons to raise and lower this number. A single press
 resultsina10RPMincrementchange.PushandholdeachbuttontoscrollmorequicklythroughtheRPMscale.Onceyouhavedialedinthedesiredset
point, press ENTERtoconrmyourchoice.NavigatetoadditionalshiftpointsettingsbypressingtheMODE (+) button. Set these additional points using
the process described above.
NOTE:  Itisrecommendedthatyousettheshiftpointto3000RPM(orasimilarlymidtolowpointinyourengine’srevrange)toconrmproperinstallation.
    WiththeDPSonandinTachmode,bringtherevsofthevehicleto3000RPMandverifythatthelightactivatesasspecied.Oncethistestis
    completeddialupyourshiftpointtoyourdesired,orenginebuilderspeciedRPMsetting.
NOTE:  Ifasetpointhasbeenchanged,allhigherShift-Litesetpointswillalsobechangedtothesamevalue.AlllowerShift-Litesetpointswillbeleft
    unchanged.Forexample,ifShift-Litesetpoint#2ischangedto6,000RPM,setpoints#3and#4willalsobechangedto6,000RPM.
    Setpoint#1willnotbechanged.Setpoint#5istheLaunchRPMandwillnotchangewhensetpoints#1-4arechanged.
E.) *LAUNCH LITE SET – TheDigitalProShifthasaLaunchLitesettingfordragracingapplicationsandother
 formsofmotorsportthatcanbenetfromapreciselaunchRPMfromadeadstop.WhentheLaunchLiteisactive,theshiftlightwillperformasfollows:
  •WhentheRPMisbelowtheLaunchRPMSetPoint:theshiftlightwillbeo.
  •WhentheRPMisattheLaunchRPMsetpoint+/-100RPM:theshiftlightwillbeon.
  •WhentheRPMisabovetheLaunchRPMsetpoint:theshiftlightwillash.
Press the MODE (+)buttonuntil“SptS”isdisplayed,pressENTERtoconrmthischoiceandthenpressMODE (+)until“LnCH”isdisplayed.
Press ENTERtoconrmyourchoicetosetyourlaunchlightRPM.UsetheMODE (+) and EXIT (–)buttonstoscrollupanddownuntilyourdesiredRPM
set point is displayed. Press ENTERtoconrmyourLaunchLitesetpoint.
* LAUNCH RPM QUICK SET –IfyouneedtochangeyourLaunchLightSettingquickly,youcandosowhenthevehicleengineisrunningandtheDigital
 ProShiftisonbyraisingtheengineRPMin“TachMode”untilyouhavereachedthedesiredsetpoint.PresstheENTERbuttontoconrmyournew
 LaunchLightSetting.YoushouldseetheDecimalindicatorashquicklytoconrmyournewsetting.
F.) PULSE PER REVOLUTION SET (CYL. CALIBRATION) –UsethisfeaturetocalibrateyourDigitalProShifttoyourengineandignitiontype.To
 enterPulsePerRevolutionSet,presstheMODE (+)buttonuntil“PPr”isdisplayed,thenpressENTERtoconrmyourselection.Youmaynowusethe
“+” and “–” buttons to cycle up and down through the pulse settings available on this product. Pulse per revolution settings refer to the number of pulses
 or“plugrings”providedbytheignitiontothedeviceperenginecrankrevolution.Forexampleasinglecoilignitionona4-cylinderenginewilltypicallyre
 twocylinderspercrankrevolution.Ifyourignitionmatchedthistype,youwouldneedtosetyourPPrvalueto“2”(
†
See below). Below is a list of common
 ignitionpulsesettings.IfyouneedfurtherassistancecalibratingthisunitforyourapplicationpleasevisitourTechTipsandFAQsectiononourwebsite
(http://www.autometer.com/tech_faq.aspx) or contact AutoMeter tech support personnel via the information included with the warranty information
shown later on this sheet.
†
The available ignition pulse settings are .5, 1, 1.5, 2, 2.5, 3, 4, 5 & 6.
B.) RECORD MODE –TheDPSmustbein“Preset”modebeforetheRecordmodecanbestarted.
 Thisisaccomplishedbyapplying+12vtotheBluewire.Thiscanbedonewitharemotestartswitch,
 transbrakeorlinelocksolenoid,brakeswitchorclutchswitch(refertotheWiringdiagram).Therightmost
 decimalpointshouldnowbeblinkingindicatingthatyouhaveentered“Preset”mode.
 WhileinPresetmode,theLaunchLitefunctionwillbecomeactive.Inthismode,theShift-Litewill
perform as follows:
 WhentheRPMisbelowtheLaunchRPMSetPoint:theShift-Litewillbeo.
 WhentheRPMisattheLaunchRPMsetpoint+/-100RPM:theShift-Litewillbeon.
 WhentheRPMisabovetheLaunchRPMsetpoint:theShift-Litewillash.Oncetheunitenters
 Recordmode,theLaunchLitefunctionwillnolongerbeactive.
 TostartarecordingfromPresetmode,removethe+12voltstothebluewire(refertotheWiringdiagram).
The right-most decimal indicator will change to a constant lit state indicating recording is in progress.
NOTE:WheneveraRecordModeisstarted,anypreviouslyrecordedruninformationwillbeover-written.
 Thedevicewillcontinuetorecordforthespeciedmaximumtimeperiod(80seconds),oruntilEXIT(–)ispressed,or+12volts
 isre-appliedtotheBluewire,whichevercomesrst.Thedecimalindicatorwillturnoattheendoftherecording.
NOTE:DuringtheRecordMode:
• 450RPM“ShortShiftProtection”isprovided.Thiswilladvancetheshift-litesettingfromoneshiftpointtothenextwhenthe
 enginedrops450RPMormore.Forexample,ifshiftpoint#1issetat6,000RPMandyoushortshiftat5,000RPMthetach
 willautomaticallyadvancetoshiftpoint#2eventhoughyouneverreached6,000RPMandthelightneverturnedon.
• Duringarun,afterthelastshiftpoint,theShift-LitealwayscomeonatRPMSettingofthelastshiftpoint.
 Iftheunitispowereddownduringarecording,thetachwillreturnto“Tach”modewhenpowerisappliedandtheengineis
running. The recording will be available for playback up to the point that power was removed.
SETUP and OPERATION MODES
A.) MENU MODE – To Select Menu Mode, press the MODE (+) button. To exit setup mode and return to
 RealTimedisplay,pressEXIT (–).
ENGINE Most 2 cyl. Most 4 cyl. Most 6 cyl. Most 8 cyl.
PPR 0.5 1 1.5 2.0 2.5 3 4 5 6

Auto Meter Digital Pro Shift Specifications

General

Brand	Auto Meter
Model	Digital Pro Shift
Category	Automobile Accessories
Language	English