Autotrol 460i - User Manual

Questions and Answers

T
Timothy StewartAug 20, 2025
Why Autotrol 460i Control Systems will not regenerate automatically or when button is pressed?
- C
  Cathy MerrittAug 20, 2025
  If your Autotrol Control Systems won't regenerate automatically or when the button is pressed, check the following: * Make sure the electric cord is plugged in and connected to a working outlet. * A defective motor, broken gear, binding in the gear train, or defective switch could be the cause. In any of these cases, the timer should be replaced.
J
Jennifer FosterAug 22, 2025
What to do if Autotrol 460i Control Systems timer is stalled in regeneration cycle?
- J
  Julie NicholsAug 22, 2025
  If the Autotrol Control Systems timer is stalled in the regeneration cycle, here are some things to check: 1. **Power:** Ensure the unit is plugged into a working outlet. 2. **Timer components:** Issues like a dead motor, a motor running backwards, a broken gear, or a defective switch all require replacing the timer. 3. **Other issues:** Check for air leaks in brine connections, binding of the camshaft, or water pressure exceeding 125 psi during regeneration (install a pressure regulator if needed). 4. **Defective circuit board:** Replace the timer.
H
hernandezedwardAug 25, 2025
Why Autotrol 460i will not regenerate automatically but will regenerate when button is pressed?
- M
  Melissa SimpsonAug 26, 2025
  If Autotrol Control Systems will not regenerate automatically but will regenerate when button is pressed, it could be due to: * A water flow display that is not working. Refer to troubleshooting for the 'No water flow display' issue. * A defective circuit board. In this case, replace the timer. * Incorrect hardness and capacity settings. Set to correct values.
J
Jennifer FoxAug 28, 2025
Why does my Autotrol 460i regenerate at the wrong time of day?
- A
  Ashley LewisAug 28, 2025
  If your Autotrol Control Systems regenerates at the wrong time of day, it's likely due to: * Power outages: Reset the clock to the correct time of day. * Incorrect clock settings: Reset the clock to the correct time of day.
B
Brooke AlexanderAug 31, 2025
Why Autotrol 460i Control Systems clock does not display correct time of day?
- C
  Cindy ClarkAug 31, 2025
  If the clock on your Autotrol Control Systems does not display the correct time of day: * Ensure the outlet is not controlled by a switch. Use an outlet that is always on. * Incorrect voltage or frequency (Hz) can cause time display issues. Replace the timer with one of the correct voltage and frequency (Hz). * After power outages, reset the clock.
J
James SandovalSep 2, 2025
What to do if there is no water flow display when water is flowing with Autotrol Control Systems?
- L
  Laura CarterSep 2, 2025
  If there is no water flow display when water is flowing in your Autotrol Control Systems, consider these potential causes: * Ensure the bypass valve is not in the bypass position. * Check that the meter probe is fully inserted into the meter housing. * Remove any foreign material that may be restricting the meter turbine's rotation, and flush with clean water. If the turbine doesn't spin freely, replace the meter. * A defective meter probe or circuit board may be the cause. In any of these cases, the timer should be replaced.
R
Rachel McdanielSep 5, 2025
What to do if Autotrol 460i Control Systems time display shows something other than time of day?
- J
  jeannekingSep 5, 2025
  If the time display on your Autotrol Control Systems shows something other than the time of day, it could be due to electrical interference or a defective circuit board. Try disconnecting power to the unit, then restore power and reset the time of day display. If the problem persists, replace the timer.
C
Christopher ThompsonSep 8, 2025
How to fix Autotrol Control Systems clock that does not display time of day?
- C
  cookcoreySep 8, 2025
  If the clock on your Autotrol Control Systems isn't showing the time of day, here's what to check: * **Power cord:** Make sure the transformer cord is plugged in. * **Outlet:** Verify the outlet has power; if not, repair it or use a working outlet. * **Transformer:** If the transformer is defective, it will need to be replaced. * **Circuit board:** A defective circuit board will require replacing the timer.
K
Kayla MezaSep 12, 2025
Why Autotrol Control Systems camshaft does not stop at the end of regeneration?
- S
  Sheila DeleonSep 12, 2025
  If your Autotrol Control Systems is in continuous regeneration and the camshaft doesn't stop, it's likely due to a broken switch activator on the gear or a defective switch. In either case, the timer should be replaced.
B
Bradley CollinsSep 13, 2025
Why does the time display continue to advance on my Autotrol 460i Control Systems?
- C
  Carrie KramerSep 13, 2025
  If the time display on your Autotrol Control Systems continues to advance, it indicates a defective time set switch. The solution is to replace the timer.