Why does my Autotrol Performa 440i Control Control Systems timer not display the correct time?
If the Autotrol Control Systems timer does not display the correct time of day, ensure the outlet is not controlled by a switch. If power outages occur, reset the time of day.
Why Autotrol Control Systems control does not regenerate automatically?
If your Autotrol Control Systems control will not regenerate automatically, ensure the transformer is plugged in and that there is electric power at the outlet. If these are not the cause, the motor, gear, gear train, or switch may be defective, in which case the control needs to be replaced.
How to fix Autotrol Performa 440i Control Control Systems that regenerates at wrong time of day?
If the Autotrol Control Systems control regenerates at the wrong time of day, reset the time of day and regeneration to the correct settings. This could be due to power outages or incorrect time settings.
How to fix Err 2 on Autotrol Performa 440i Control?
To resolve Err 2 on your Autotrol Control Systems, press any key to silence the alarm. The control will then turn the motor on and drive the camshaft to the proper location. If the valve camshaft has been manually rotated out of the 'regeneration complete' position, or if there is a faulty motor, motor drive or switch, replace the control.
What to do if Autotrol Performa 440i Control Control Systems shows Err 3?
To resolve Err 3 on your Autotrol Control Systems, the control will turn the motor on and drive the camshaft to the proper location. If the error persists, it may be due to a faulty motor, motor drive, or switch, in which case you should replace the control.
How to solve Err 4 on Autotrol Performa 440i Control?
To fix Err 4 on your Autotrol Control Systems, adjust the settings that are out of the allowable range. Hardness should be between 3 and 250, capacity between 0.1 and 140.0, refill control between 1 and 99, and brine draw value according to Table 2.
Why Autotrol Control Systems control regenerates only when REGEN button is depressed?
If your Autotrol Control Systems control does not regenerate automatically but does regenerate when the REGEN button is depressed, refer to item 5 in this table if the water flow display is not operative. Otherwise, set new control values and refer to the Programming section, or replace the control if the circuit board is defective.
What does Err 1 mean on Autotrol Control Systems?
To resolve Err 1 on your Autotrol Control Systems, press any key to load default values. Then, refer to the 'Programming the Model 960 Control' section for further instructions.
Why does Autotrol Control Systems timer not display time of day?
If the Autotrol Control Systems timer does not display the time of day, connect the transformer to power or repair the outlet if there is no electric power. If the issue persists, the transformer or circuit board may be defective, requiring replacement of the transformer or the entire control.
What to do if Autotrol Performa 440i Control Control Systems runs out of treated water between regenerations?
If you run out of treated water between regenerations with your Autotrol Control Systems, repeat regeneration ensuring the correct salt dosage is used. Other causes may include a fouled resin bed (use resin cleaner), incorrect factor 1 or capacity settings (set to correct values), restricted meter turbine rotation due to foreign material in the meter housing (remove meter housing, free up turbine, and flush with clean water; replace meter if turbine does not spin freely), or excessive water usage below 1/5 gallon per minute (repair leaky plumbing and/or fixtures).
Choosing an optimal location for the water conditioner unit, considering distance to drain and water heater.
Connecting the water supply to the conditioner, recommending a bypass valve system.
Guidelines for connecting the drain line, including tubing size and elevation.
Step-by-step process to put the water conditioner into service after installation.
Instructions for connecting the control unit to the electrical power source.
Methods for automatic regeneration: calendar override or metered usage.
General steps to remove the valve assembly from the tank.
Step-by-step guide to safely remove the 440i control unit.
Step-by-step guide to safely remove the 940F and 960F control units.
Common problems and solutions for the control valve itself.
Specific issues and fixes for 440i and 940F control units.
Specific issues and fixes for the 960F control unit.
Explains alarm indications, causes, and solutions for the 960F control.
Lists common problems and solutions for the 960 control system.
Additional common problems and solutions for the 960 control system.
General| Model | Performa 440i |
|---|---|
| Operating Pressure | 20-125 PSI |
| Operating Temperature | 34 - 120°F (1 - 49°C) |
| Display | LCD |
| Mounting | Tank Mounted |
| Compatibility | Water Softeners, Filters |
To Next Page
