Aviom A-16II - User Manual

Other manuals for Aviom A-16II

Quick Reference2 pages

Questions and Answers

V
Vanessa JacksonAug 15, 2025
How to troubleshoot no audio from Aviom Mixer outputs?
- J
  Juan PhillipsAug 15, 2025
  If you're not getting any sound from your Aviom Mixer outputs, start by checking the levels on the main mixing board connected to the system. Also, inspect the cables and connections between the main mixer and the personal monitor system. The signal LEDs on the front of the input module can help you confirm if audio is being received. Try replacing the cables to eliminate them as a potential issue. Ensure that all channels and the master volume on the personal mixer are not set to zero. Finally, verify that the A-Net cables are correctly connected.
J
Joseph AliAug 18, 2025
Why the A-Net LED is on but there is no sound from Aviom Mixer?
- J
  James ParsonsAug 18, 2025
  The A-Net Active LED indicates that the input to the receiving device is properly connected to another A-Net device. It doesn't guarantee that all devices in the system are correctly connected. If you have two Aviom Mixers connected, the second mixer's A-Net LED might light up simply because it's connected to the first. Ensure each device in the chain has a Category 5 cable plugged into it. Also, verify that the A-Net cables are connected in the correct order, with the cable from the first mixer connected to the A-Net In jack and subsequent devices connected from the Out of the previous device to the In of the next.
M
Melissa SawyerAug 21, 2025
What to do if Aviom Mixer preset was not saved?
- B
  Brian MerrittAug 21, 2025
  If your Aviom Mixer isn't saving your Preset, ensure you're holding down both the RECALL and GROUP buttons before pressing a memory location button. The Preset saves when you release your finger from the memory location button. A successful save is indicated by all sixteen Channel LEDs flashing momentarily.
M
Mikayla JohnstonAug 25, 2025
Why Aviom Mixer preset recalls channels in mono or linked incorrectly?
- D
  Dean BauerAug 26, 2025
  If you recall a Preset on your Aviom Mixer and the stereo link status is different from when it was saved, the Preset will adjust to match the current hardware settings on the input module's front panel, which are determined by the Link switches. To resolve this, simply change the position of the Link switch on the input module to match your desired stereo link setting. Your current mix will update immediately.
A
Anthony ClarkAug 28, 2025
Why I can’t hear a Channel that is part of a Group on Aviom Mixer?
- K
  Kim OchoaAug 28, 2025
  If you can't hear a channel that's part of a Group on your Aviom Mixer, the Group might be muted. Check the lower (yellow) LED in the Channel buttons; a lit yellow LED indicates the Channel is muted. To unmute it, press the MUTE button while the Group is selected, ensuring the yellow LED is unlit. Also, the Channel volume might be too low. In Group edit mode, select the Channel and check the level using the LEDs in the Volume indicator. If no LEDs are lit, the Channel volume is all the way down. Adjust the volume using the Channel VOLUME knob, and re-save the Group and Preset if needed.
K
Kathryn FosterAug 31, 2025
How to change presets on Aviom Mixer?
- J
  Jose Cohen IVAug 31, 2025
  If you're having trouble changing Presets on your Aviom Mixer, ensure that you've pressed the RECALL button. The RECALL button's LED will flash, indicating that you should press a numbered button to recall a Preset.
E
Ethan RobersonSep 4, 2025
Why Aviom Mixer channel assigned to a Group suddenly changed?
- J
  Justin RogersSep 4, 2025
  If a Channel on your Aviom Mixer has been assigned to one Group and suddenly becomes part of a different Group, it's possible that channel characteristics changed when linking a pair of channels with the Link switch on the input module after a Group was created. Remember that the even-numbered channel (right side) will inherit the characteristics of the odd-numbered channel (left side), including volume, pan, mute status, and Group assignment.
J
Jessica MathewsSep 7, 2025
Why in Group mode, I can’t select a new Channel on Aviom Mixer?
- K
  Kenneth WilsonSep 7, 2025
  If you're trying to select a new Channel in Group mode on your Aviom Mixer and nothing happens, it's likely that you've already defined the maximum of three Groups. The button press will be ignored if you attempt to create a new Group that exceeds this limit. To continue, edit or delete an existing Group.
S
Sarah HarrisSep 12, 2025
Why when editing a Group with many Channels, all of the LEDs are pulsing on Aviom Mixer?
- A
  alexanderharrisSep 12, 2025
  This pulsing effect on the LEDs when editing a Group with many Channels on your Aviom Mixer is normal. It's due to the current-limiting circuit and doesn't indicate a problem.

Summary

Important Safety Instructions

Aviom, Inc. Limited Warranty

A-16 II Personal Mixer Components

Monitor System Setup

Power Connection

Connect the DC power supply to the A-16II Personal Mixer unit.

System Connections

Connect A-Net compatible devices using Cat-5e cables in a series.

Audio Connections

Powering Up

A-16 II Features

Operational Modes

Explains the different modes: Mix Mode, Recall Mode, and Group Mode.

Global Controls

Tone Controls

Use Bass and Treble controls to adjust overall mix frequencies.

Master Volume

Personal Mixer Rear Panel

A-Net Connectors

Describes the A-Net In and Out jacks for system connectivity.

DC Power Input

Details the connection point for the DC power supply.

Audio Outputs

Explains the headphone/line output jack and its uses.

Making a Mix

The Editing Interface

Explains the interface for editing channel settings like volume and pan.

Setting Channel Volume

Setting Pan

Details how to adjust channel panning using the Pan knob and LEDs.

Linking Channels

The Mute and Solo Functions

Solo a Channel

How to listen to a single channel by muting others.

Mute a Channel

Unmute a Channel

How to unmute a previously muted channel.

Creating Groups

Saving a Preset

Troubleshooting

No audio from Personal Mixer outputs

Cant change Presets

I dont think my Preset was saved.

Cant hear a channel that is part of a Group

The A-Net LED is on, but there is no sound

Preset recalled with incorrect link;mono status

A-16 II Personal Mixer Specifications

Aviom A-16II Specifications

General

Channels	16
Stereo Channels	8
Inputs	16
Output Type	Analog
Output	16
Network Protocol	A-Net
Power	12V DC
Power Supply	External
Sample Rate	48 kHz
Bit Depth	24-bit
Dimensions	1.75"
Input Connectors	RJ45
Output Connectors	1/4" TRS

Related product manuals