If the product complies with the requirements of the RoHS Directive (2011/65/EU) and does not contain any hazardous
substances in quantities exceeding the permitted limits, residues may still be present. Observe the following safety
instructions to avoid chemical hazards: Caution: Soldering can produce vapours that can be harmful to health. Note: Use a
soldering vapour extractor or work in a well-ventilated area. Wear a breathing mask if necessary. Caution: Some people may
be sensitive to certain materials or chemicals contained in the product. Note: If skin irritation or allergic reactions occur,
discontinue use and consult a doctor if necessary. Caution: Keep the product out of the reach of children and pets to avoid
accidental contact and ingestion of small parts. Note: Keep
Store the product in a secure, closed container when not in use. Caution: Avoid contact of the product with food and drink.
Note: Do not store or use the product near food to prevent contamination. The product contains sensitive electronic
components and sharp edges. Improper handling or installation can lead to injury or damage. Observe the following safety
instructions to avoid mechanical hazards: Caution: The circuit board and the connections of the product may have sharp
edges. Proceed with caution to avoid cutting injuries. Note: Wear suitable protective gloves when handling and installing the
product. Caution: Avoid excessive pressure or mechanical stress on the circuit board and components. Note: Only mount the
product on stable and level surfaces. Use suitable spacers and housings to minimise mechanical stress. Caution: Ensure that
the product is securely fastened to prevent it from accidentally slipping or falling. Note: Use a suitable base or secure
fastening in housings or on mounting plates. Caution: Ensure that all cable connections are securely and correctly connected
to prevent tensile loads and accidental disconnection. Note: Route cables so that they are not live and do not pose a tripping
hazard. The product works with electrical voltages and currents that can lead to electric shocks, short circuits or other hazards
if used improperly. Observe the following safety instructions to avoid electrical hazards: Caution: Only use the product with
the specified voltages. Note: The power limits of the product can be found in the corresponding data sheet Caution: Avoid
short circuits between the connections and components of the product Note: Ensure that no conductive objects touch or
bridge the circuit board. Use insulated tools and observe the arrangement of the connections.
Caution: Do not carry out any work on the product when it is connected to a power source. Note: Disconnect the product
from the power supply before making any changes to the circuit or connecting or disconnecting components. Caution: Do not
exceed the specified current levels for the inputs and outputs of the product. Note: The power limits of the product can be
found in the technical specifications or in the data sheet Caution: Ensure that the power sources used are stable and
correctly dimensioned. Note: Only use tested and suitable power supply units to avoid voltage fluctuations and overloads.
Caution: Maintain sufficient distance from live parts to avoid unintentional contact. Note: Ensure that the cabling is arranged
safely and clearly according to the voltage used. Caution: Use insulating housings or protective covers to protect the product
from direct contact. Note: Place the product in a non-conductive housing to prevent accidental contact and short circuits. The
product and the components on it can heat up during operation. Improper handling or overloading of the product can lead to
burns, damage or fire. Observe the following safety instructions to avoid thermal hazards: Caution: Ensure that the product is
used within the recommended operating temperatures. Note: The recommended operating temperature range is typically
between-40°C and
+85°C. Check the specific information in the product data sheet. Caution: Do not place the product near external heat sources
such as radiators or direct sunlight. Note: Ensure that the product is operated in a cool and well-ventilated area. Caution:
Ensure that the product is well ventilated to prevent overheating. Note: Use fans or heat sinks if the product is operated in a
closed housing or in an environment with limited air circulation. Caution: Mount the product
on heat-resistant surfaces and in heat-resistant housings. Note: Use materials for enclosures that can withstand high
temperatures to avoid damage or fire hazards. Caution: Implement temperature monitoring when using an enclosure and, if
necessary, protective mechanisms that switch off the product if it overheats. Note: Use temperature sensors and appropriate
software to monitor the temperature of the product and switch off the system if necessary. Caution: Avoid overloading, which
can lead to excessive heating of the components. Note: Do not exceed the specified limit values.
The current and voltage are regulated to prevent overheating. Caution: Short circuits can generate considerable heat and
cause fires. Note: Ensure that all connections are correct and secure and that no conductive objects can inadvertently cause
short circuits.
To Next Page
Loading...