B.E.G. LUXOMAT PD4-M-1C Series - User Manual

1
1 2
2
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
2000
1200
600
200
40
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
IR-PD
IR-PD-Mini
B.I.T.
Q.C.
PASSED
1
3. Putting into operation / Settings
Follow-up time for light control
The time can be set infinitely variably at between
15 seconds and 16 minutes.
Symbol
: impulse < 1sec.
Symbol
TEST: Test mode
(Every movement switches on the light for a period of 1
second, switching it off for a period of 2 seconds after that
regardless of the level of brightness.)
Twilight-switch for light control (relay 1)
The switch-on value for the light can be set at between 10
and 2000 Lux. Using the rotary control, the luminance set
points can be set as desired.
Symbol
: Night-time operation
Symbol
: Daytime/Night-time operation
Installation and Operating Instruction for B.E.G. - Occupancy detectors PD4-M-1C-FC/-FM
The detector can be installed
in conventional inlet-sockets
mounted on the ceiling.
The assembly plate enclosed
must be stripped off prior to
installation and secured to
the ceiling using 4 screws
and ensuring that it is not
laterally transposed.
Having connected up the
cables in accordance with
regulations, the detector can
be placed in position as
shown in the drawing op-
posite and, applying a little
pressure, can then be locked into position with
the assistance of the spring clips.
2b. Installation of the LUXOMAT
®
PD4-M-1C-FM
Unlocking device
Lock device
4. Settings carried out using remote control (optional)
Remote control LUXOMAT IR-PD
1. Check Battery:
open battery compartment by pressing the
plastic springs together and removing the
battery-holder.
2. IMPORTANT
Please pay attention, that the setting is Potentio-
meter 1 at “TEST” and Potentiometer 2 not at
“SUN”. All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position “TEST/
SUN”. Please switch Potentiometer 2 over to
“MOON” or any other value.
Caution:
Settings with remote control supersede the
settings by courtesy of potentiometers.
LUXOMAT
®
PD4-M-1C
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by qualified
professionals or by instructed persons
under the direction and supervision
of qualified skilled electrical person-
nel in accordance with electrotechni-
cal regulations.
Disconnect supply before installing!
When in Master/Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
Lock device
Test mode
Reset to deactivate
Resetting when closed
The lighting relay is switched off, i.e.
opened and the follow-up times reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is illuminated).
This operating mode can only be activated during the period of
5 seconds after pressing the “lock“ button. This status will only
permit actuating the function “Light on/Light off”.
The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
4. Apply current
5. Open detector
Light on/off
The light will remain switched on/off for as long as movements
are detected in the areas of coverage. Once the last movement
has been detected, the light will remain on for the duration of the
follow-up time as per setting.
The appliance will then return independently to the mode
selected (Fully or Semi-automatic).
2a. Installation of the LUXOMAT
®
PD4-M-1C-FC
The detector has
been designed and
developed specifi-
cally for installation in
suspended ceilings.
A circular opening of
diameter 68 - 70 mm
must first of all be pro-
duced in the ceiling.
Having connected up the cables in accordance
with regulations, the detector is inserted into
the opening as shown in the drawing opposite
and fixed into position with the assistance of the
spring clip.
Option:
Wall bracket for remote
control IR-PD


max
50
Lux
1500
Lux
ON
OFF
max
50
Lux
1500
Lux
ON
OFF






max
50
Lux
1500
Lux
ON
OFF
Luminance set point
Automatic reading in the current light value
as new luminance set point
Individual light value 2 - 2500Lux
Follow-up time (relay and channel 1)
15 sec. up to 30min.
Impulse function (relay and channel 1)
1sec. ON, 9sec. OFF
Preset/user mode
Fully automatic/semi automatic mode => (see page 2, point 5)
Semi automatic: red LED (ashing),
Fully automatic: red LED on for ca. 3 sec.
Resetting when open
All values which have been programmed using the remote
control IR-PD are deleted, and those values which have
been set by potentiometer are activated.
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
2c. Self test cycle
The product enters an initial 60-sec-
ond self-test cycle, when the supply
is first connected. The occupancy
detector is ready for operation.
GB

Summary

Mounting Preparations

Disconnect Supply Before Installing

Warning to disconnect power before proceeding with installation to ensure safety.

Master;Slave Mode Daylight Placement

Advice on placing the Master appliance in an area with the least daylight for Master/Slave operation.

Installation of LUXOMAT PD4-M-1 C-FC

Installation in Suspended Ceilings

Details for installing the detector within suspended ceilings, requiring a 68-70mm opening.

Installation of LUXOMAT PD4-M-1 C-FM

Installation in Ceiling Inlet-Sockets

Instructions for mounting the detector using ceiling inlet-sockets and provided assembly plate.

Self Test Cycle

Initial 60-Second Self-Test

Describes the product's initial 60-second self-test cycle upon first power connection.

Putting Into Operation and Settings

Follow-Up Time for Light Control

Setting the delay time for the light control, adjustable from 15 seconds to 16 minutes.

Twilight-Switch for Light Control

Setting the light level threshold (10-2000 Lux) for light control activation.

Settings Using Remote Control (Optional)

Check Battery

Procedure to open the battery compartment and check the remote control battery.

Important: Potentiometer Settings

Critical note on potentiometer settings when using remote control for programming.

Caution: Settings Priority

Warning that remote control settings override potentiometer settings.

Fully;Semi Automatic Mode

Fully Automatic Operation

Light switches on/off automatically based on presence and ambient brightness.

Semiautomatic Operation

Light requires manual switch-on; switches off automatically based on presence.

Manual Switching

Manual Lighting Control

Procedure for manually switching the lighting on and off via a pushbutton.

Range of Coverage

Coverage Area Details

Illustrates the detection range (Ø) for seated, walking towards, and tangential movement.

Exclude Sources of Interference

Limiting Detection Range

Using masking clips to reduce or limit the sensing area coverage.

Article; Part Nr.; Accessory

Product Codes and Accessories

Lists part numbers for PD4-M-1C models and available accessories like remote controls.

Wiring Diagrams

Terminal Connection for Standard Operation

Diagram showing wiring connections for a single detector unit.

Terminal Connection for Master;Slave Operation

Diagram illustrating connections for Master/Slave configuration with multiple units.

Technical Data PD4-Master-1 C

Sensor and Power Supply Specifications

Provides technical details including power supply, ambient temperature, and protection class.

Detection Area and Mounting Height

Specifies the coverage area, recommended mounting height, and light measurement details.

Relay;Channel 1 Specifications

Details on the contact type, load capacity, and electronic ballast compatibility.

Dimensions and Visible Portion

Provides physical dimensions (H x Ø) and the visible portion when installed.

Technical Data PD4-Slave

Slave Unit Electrical Data

Specifies that electrical data for the Slave unit is the same as Master, with one channel for motion.

CE Declaration of Conformity

Compliance Standards

Confirms product compliance with Low Voltage and EMV recommendations.

LED-Functional Indicators, Fault-Finding

Red LED Indicators

Explains the meanings of red LED states for self-checking, EEPROM status, and movement detection.

Red LED for Command Acknowledgement

Indicates LED signals for validly received commands or blocked detectors.

Green LED Indicators

Details the green LED states related to 'Permanent protection against sabotage' mode.

B.E.G. LUXOMAT PD4-M-1C Series Specifications

General

Brand	B.E.G.
Model	LUXOMAT PD4-M-1C Series
Category	Security Sensors
Language	English