Baby Lock Enterprise BNT10L User Manual (English)

Other manuals for Baby Lock Enterprise BNT10L

Questions and Answers:

N
npatrickAug 21, 2025
How to fix skipped stitches on my Baby Lock Enterprise BNT10L?
- F
  Frank HamiltonAug 21, 2025
  Skipped stitches can occur due to: * Incorrect upper thread threading: Thread the upper thread correctly. * Damaged needle: Replace a bent or blunt needle with a new one. * Incorrect needle installation: Correctly install the needle. * Dust accumulation: Clean the hook and the needle plate. * Thread twist: Improper twisting results in irregular loop formation. Try using a new spool.
K
Kimberly GriffinAug 25, 2025
Why does my Baby Lock Enterprise BNT10L Sewing Machine upper thread keep breaking?
- D
  deborah27Aug 25, 2025
  The upper thread may break because: * The needle is not correctly installed: Correctly install the needle. * The needle set screw is loose: Use the Allen screw driver to tighten the needle set screw. * The needle is bent or blunt: Replace the needle with a new one. * The area around the hole in the needle plate is damaged: Replace the needle plate. * Using a specialty thread like a metallic thread: Slow down the machine sewing speed.
M
michael80Aug 27, 2025
Why does my Baby Lock Enterprise BNT10L bobbin thread keep breaking?
- A
  Amanda DuncanAug 28, 2025
  The bobbin thread may break due to: * Incorrect threading: Ensure the bobbin thread is correctly threaded. * Damaged bobbin: Replace the bobbin if it's scratched or doesn't rotate smoothly. * Damaged bobbin case: Replace the bobbin case if it's damaged. * Tangled thread: Remove any jammed thread and clean the hook. * Incorrect bobbin: Use the correct bobbin specifically designed for your machine.
R
Raymond HuffAug 29, 2025
What to do if my Baby Lock embroidery machine does not operate?
- S
  stephenscatherineAug 29, 2025
  If your embroidery machine isn't working: * Make sure the machine is turned on. * Touch the unlock key to unlock the machine. * Press the start/stop button after unlocking the machine.
D
Derek EwingAug 31, 2025
Why is my Baby Lock Enterprise BNT10L Sewing Machine so noisy?
- C
  Chase FuentesAug 31, 2025
  A noisy machine could be due to: * Lint in the hook: Clean the hook. * Incorrect upper thread threading: Check the thread path, and then thread the upper thread again. * Not enough oil: Oil recommended parts.
D
Dennis MckeeSep 1, 2025
How to fix loops in the upper thread of my Baby Lock Enterprise BNT10L?
- J
  Jessica DuffySep 2, 2025
  Loops in the upper thread can be caused by: * Low upper thread tension: After passing the upper thread through the hole in the presser foot, pull the thread by hand to check the thread tension. * Threading issues around tension discs: Clean upper thread tension disc. Rethread and make sure tension disc rotates when pulling on thread. * Poor thread quality: Try sewing with different thread. If the problem no longer occurs after the thread is changed, replace the thread with one of good quality.
R
Robin DennisSep 3, 2025
Why is the thread tension incorrect on my Baby Lock Enterprise BNT10L Sewing Machine?
- A
  Ashley HudsonSep 3, 2025
  Incorrect thread tension can result from: * Incorrect upper thread threading: Check the thread path, and then thread the upper thread again. * Incorrect bobbin thread threading: Correctly thread the bobbin thread. * Incorrect lower thread tension: Adjust the tension of the bobbin thread.
M
Matthew HerringSep 5, 2025
What to do if my Baby Lock Sewing Machine has needle cuts or holes in the garment?
- M
  Mr. Brian TurnerSep 5, 2025
  Needle cuts or holes in the garment may be caused by: * Dull needle: Replace the needle. Dull needles have a difficult time passing through the garment, causing fabrics to tear. * Delicate fabric: Use stabilizer on top of fabric.
S
Shari BrownSep 6, 2025
What to do if my Baby Lock Enterprise BNT10L upper thread comes out of the needle?
- C
  Christina SmithSep 7, 2025
  If the upper thread comes out of the needle when embroidering begins, and if a short length of thread remains after the thread is trimmed, set the remaining length of thread to “Long Tail” on the second page of the settings screen.
D
Dominic LarsenSep 8, 2025
What to do if my Baby Lock Sewing Machine upper thread does not reach the bobbin thread?
- D
  Debra MooreSep 8, 2025
  If the upper thread doesn't reach the bobbin thread when embroidering begins, it might be because there is no more thread in the bobbin, the thread does not feed from the bobbin, or the thread that is fed from the bobbin is too short. Correctly thread the lower thread.

Baby Lock Enterprise BNT10L Specifications

General

Number of Needles	10
Built-in Designs	Yes
Display	LCD Touch Screen
Connectivity	USB
Needle Threading System	Automatic
LCD Screen	Yes
USB Port	Yes
Automatic Thread Cutter	Yes
Type	Embroidery
Maximum Embroidery Speed	1000 spm