Baileigh Industrial DP-1200VS

Questions and Answers

V
Vanessa PachecoAug 13, 2025
Why does the drill bit burn or smoke on my Baileigh Industrial DP-1200VS Power Tool?
- S
  scottsmithAug 13, 2025
  If your Baileigh Industrial Power Tool's drill bit burns or smokes, several factors could be at play. It might be due to an incorrect speed, which requires adjustment. Another reason could be that chips are not coming out of the table; in this case, retract the bit frequently to clear them. A dull bit can also cause this issue, so consider sharpening or replacing it. Feeding too slowly can also lead to burning or smoking, so increase the feed rate to allow the drill to cut effectively. Insufficient lubrication can also be a culprit, so be sure to lubricate the bit. Lastly, ensure the bit isn't running backward by checking the motor rotation to confirm it is clockwise facing the shaft end.
E
ericawilsonAug 16, 2025
How to fix a Baileigh Industrial DP-1200VS when the spindle does not turn?
- E
  eric87Aug 16, 2025
  If the spindle of your Baileigh Industrial Power Tool isn't turning, there could be a few reasons. First, check the wiring, fuse, or circuit breaker to ensure there is power to the drill press. If the power supply is not the issue, the switch might be defective and need replacement. Alternatively, the motor itself could be defective, which would also necessitate replacement.
C
Christopher MitchellAug 20, 2025
What causes excessive drill runout or wobble in my Baileigh Industrial DP-1200VS Power Tool?
- K
  Kirsten WoodAug 20, 2025
  Excessive drill runout or wobble in your Baileigh Industrial Power Tool can stem from several causes. The bit might be bent, requiring replacement. Ensure the bit is correctly installed in the chuck. If the issue persists, the chuck itself might not be properly installed. Lastly, worn spindle bearings can also cause wobble, so consider replacing them.
B
Brittney WilliamsAug 25, 2025
Why is my Baileigh Industrial DP-1200VS Power Tool making a noisy operation?
- P
  porterdeniseAug 25, 2025
  Noisy operation in your Baileigh Industrial Power Tool can arise from a few sources. A worn variable speed belt might be the cause, suggesting it's time for a replacement. The spindle might be dry, so lubricating it could resolve the issue. Also, check the motor pulleys; if they're loose, tighten them as necessary.
P
Philip MartinAug 28, 2025
What to do if drilled holes are not round using my Baileigh Industrial DP-1200VS?
- M
  michael41Aug 28, 2025
  If your Baileigh Industrial Power Tool's drilled holes are not round, it could be due to improper mounting of the drill bit, chuck, or arbor; ensure these components are mounted correctly. Another possibility is a worn or broken bit, which should be replaced. Additionally, the speed or feed might be too fast, so reduce them as needed. Lastly, the workpiece might need lubrication, so use cutting fluid during drilling.
S
Sophia RiosSep 1, 2025
Why is the spindle on my Baileigh Industrial DP-1200VS Power Tool noisy?
- M
  Mr. Steven WhiteSep 1, 2025
  A noisy spindle in your Baileigh Industrial Power Tool is often due to defective bearings. Replacing the bearings should resolve this issue.
W
William ReillySep 4, 2025
What causes excessive spindle runout on a Baileigh Industrial Power Tool?
- T
  taylornancySep 4, 2025
  Excessive spindle runout on your Baileigh Industrial Power Tool is typically caused by worn or defective bearings. Replacing the bearings should solve this problem.
M
monica70Sep 8, 2025
What to do if the drill bit binds in the workpiece when using a Baileigh Industrial DP-1200VS?
- K
  kristen42Sep 8, 2025
  If the drill bit binds in the workpiece with your Baileigh Industrial Power Tool, it might be due to the workpiece pinching the bit or excessive feed. Try supporting or clamping the work and decrease the feed pressure.