BAK bakFlip User Manual

1
2
3
4
5
Remove the paper backing and apply the seal
strip to the top of the bulkhead. Trim the ends
to tightly fit to the sides of the bed. Apply along
the radius of the bulkhead back edge.
NOTE: Wipe the surface with isopropyl alcohol
before applying.
NOTE: Installations with a drop-in bed liner
will NOT require the bulkhead seal.
BULKHEAD SEAL STRIP INSTALLATION
INSTALLATION SHEET
Parts will be shipped to you directly.
Call 818-365-9000 Mon - Fri 8:30 am - 7 pm EST
or email support@bakindustries.com
1 Hard Folding Cover
2 RH, passenger side rail
3 LH, driver side rail
4 Prop rod
5 Prop rod clip
6 Buckles
7 Buckle mounting inserts
8 Buckle mounting screws
9 Bulkhead seal
27 Allen wrench
28 Washers, retainer
29 Spacers
30 Screw & washers, M6
31 Cab bumpers
32 Jack nut installer wrench
10 Drain hoses
11 Cover mounting elevator bolts
12 Cover mounting rubber washers
13 Cover mounting washers
14 Cover mounting lock washers
15 Cover mounting knob
A
16 Well nuts
17 Washers, oversize #10
18 Screws, buttonhead
19 Screw and washers, truss head
B
20 Well nuts
21 Washers, flat
22 Washers, oversize #10
23 Screws, buttonhead
24 Jack nuts
25 Washers, flat
26 Bolts 1/4-20
1
• 1100 N. Glenstone Ave. Suite 140, Springfield, MO 65802 • 818-365-9000 • bakindustries.com Part# 318B0047 Rev. 8.12.2020BAK Industries
Laurmark Enterprises, Inc., 2020
•
TOOLS RECOMMENDED
7/8”, [0.875”, (22mm)] drill bit & drill (optional)
Philips screwdriver
1/8” Hex head
T50 Torx drive
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
6
7
8
9
10
12
11
13
14
15
A
B
16
20
24
22
23
25
26
27
32
30
28
29
31
21
17
18
19
•
•
Any damaged or missing parts?
Jeep Gladiator
NOTE: The rail installation will require identifying the bulkhead hole configuration of your truck.
This will determine which hardware package, A or B, is used. This is in step 6.

BAK bakFlip Specifications

General

Material	Aluminum
Finish	Matte
Panels	4
Locking	Yes
Installation	Clamp-on
Weather Resistance	Yes
Weight Capacity	300 lbs

Summary

BAKFlip Installation Overview

Tools and Initial Preparation

Lists required tools and instructions for bulkhead seal strip installation.

Bed Liner Preparation Steps

Liner Trimming for Fitment

Trimming the bed liner and tailgate liner for proper cover installation.

Drain Holes and Rail Cap Prep

Drilling drain tube holes and preparing bed rail caps.

Install Rails with Type A Hardware

Bulkhead Configuration & Rail Mounting

Identifying bulkhead holes and attaching rails using well nuts.

Securing Rear Rail Mounts

Installing and tightening rear rail hardware.

Install Rails with Type B Hardware

Bulkhead Configuration & Jack Nut Mounting

Identifying bulkhead holes and attaching rails using jack nuts.

Securing Rear Rail Mounts (Type B)

Installing and tightening rear rail hardware with jack nuts.

Cover Assembly and Fitment

Strap Buckles & Rail Attachment

Mounting strap buckles and securing cover rails to the cab.

Cover Squareness Adjustment

Adjusting cover alignment and tightening mounting knobs.

Final Installation Steps

Cab Bumpers and Tailgate Seal

Installing cab bumpers and adjusting tailgate seal engagement.

Drain Hoses and Operation

Installing drain hoses and understanding tail panel operation.

Safe Operation and Use

Cover Positions, Warnings & Tips

Cover positions, critical warnings, and operating best practices.

Warranty and Maintenance Guide

Product Warranty Details

Overview of the product warranty period and terms.

Care, Cleaning, and Checks

Recommended cleaning, protection, and periodic maintenance checks.