Baldor 5 Series - User Manual

32 pages

Save Page as PDF

To Next Page

For Catalog Nos. ID5202-CO, ID5203-CO,

ID5401-CO, ID5402-CO, ID5403-CO, ID5405-CO

Series 5 Inverter

Installation and Operating Manual

MN783

Main Page

Table of Contents2
Introduction4
Standard Features4
Performance Features4
Protection Features5
Trimpot Adjustments5
Optional Accessory5
Electrical Ratings5
General Performance Specifications6
- Safety Notice7
Quick-Start Instructions8
Catalog Nos. ID5202-CO, ID5203-CO Quick-Start Connection Diagram10
Catalog Nos. ID5401-CO, ID 5402-CO, ID5403-CO, ID5404-CO Quick-Start Connection Diagram11
ID5SI-1 Layout12
Mechanical Specifications and Drive Layout13
Mounting Instructions14
Finger-Safe Cover14
Expanded View of Jumpers and Trimpots14
Electrical Connections Instructions15
Terminal Block Wire and Tightening Torque Specifications15
AC Line Input, Motor, and Ground Connections16
Catalog Nos. ID5202-CO, ID5203-CO Main Speed Potentiometer Connection16
Unidirectional Main Speed Potentiometer and Forward-Stop-Reverse Switch Connections17
Bidirectional Main Speed Potentiometer Connection17
Catalog Nos. ID5202-CO, ID5203-CO Voltage Following Signal Input Connection17
Catalog Nos. ID5401-CO, ID5402-CO, ID5403-CO, ID5405-CO Voltage Following Signal Input Connection18
Catalog Nos. ID5401-CO, ID5402-CO, ID5403-CO, ID5405-CO Current Following Signal Input Connection18
Manual Start Switch Connection18
Form "C" Contact or Relay Forward-Stop-Reverse Connection19
Forward-Stop-Reverse Switch Connection19
Open Collector Forward-Stop-Reverse Connection19
Drive Operating Condition and Run/Fault Relay Contact Status20
Enable Switch Connection20
Run/Fault Relay Connection20
Run/Fault Relay Output Contact Selection20
60 Hz and 50 Hz Motor Selection21
Available Torque Vs. Output Frequency21
120 Hz and 100 Hz Drive Output Frequency Selection21
Automatic Start21
Setting Selectable Jumpers21
Catalog Nos. ID5202-CO, ID5203-CO, Forward/Reverse Speed Selection22
Catalog Nos. ID5202-CO, ID5203-CO Minimum Speed Trimpot Range22
Catalog Nos. ID5401-CO, ID5402-CO, ID5403-CO, ID5405-CO Offset Trimpot22
Trimpot Adjustments22
Catalog Nos. ID5202-CO, ID5203-CO Maximum Speed Trimpot Range23
Catalog Nos. ID5401-CO, ID5402-CO, ID5403-CO, ID5405-CO Maximum Speed Trimpot23
Acceleration Trimpot Range All Models23
Deceleration Trimpot Range All Models23
Slip Compensation Trimpot Range All Models24
Boost Trimpot Range All Models24
Catalog No. ID5202-CO CL Trimpot Range25
Catalog No. ID5203-CO CL Trimpot Range25
Catalog No. ID5401-CO CL Trimpot Range25
Catalog No. IC5402-CO CL Trimpot Range25
Catalog No. ID5403-CO CL Trimpot Range25
Catalog No. ID5405-CO CL Trimpot Range25
Drive Operation26
Maximum Allowed Motor Torque Vs. Speed26
Open Ventilated Motor with External Cooling26
Drive Operating Condition and Status LED Indicator27
Fault Recovery and Resetting the Drive27
Diagnostic Leds28
- Baldor District Offices31
- Limited Warranty32

Need help?

Do you have a question about the Baldor 5 Series and is the answer not in the manual?

Baldor 5 Series Specifications

General

Brand	Baldor
Model	5 Series
Category	DC Drives
Language	English

Related product manuals

Baldor 5 Series - User Manual

Table of Contents

Baldor 5 Series Specifications

Related product manuals