Page 4 <&(%$*4.8"4,7%K'*#$"&8#L%/7*,#*%4,77%HMNNNMNIIMOPQP1 Item 63445
?@<6AR ST6;@ACSE D@CEA6E@EU6?6AFT
W(&'89"83%C8#$('4$"&8#
%
AS%T;6!6EA%6G6UA;CU%?BSU`%@EY%Y6@AB%<;SD%CEUS;;6UA%
W;SFEYCEW%VC;6%USEE6UACSE%;6@Y%@EY%<SGGSV%AB6?6%CE?A;FUACSE?-
HH^MH]^%!@U%W(&'89*9%A&&7#-%A&&7#%)"$.%A.(**%T(&83%T7'3#
1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.
6. Repair or replace damaged or
worn cord immediately.
W(&'89"83%
T"8
H]O%!@U%aMT(&83%T7'3%,89%S'$7*$
\2&(%'/%$&%H]O%!@U%,89%'/%$&%HO%@_
7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
H]O%!@U%aMT(&83%T7'3%,89%S'$7*$. The tool has
a grounding plug that looks like the plug illustrated
above in H]O%!@U%aMT(&83%T7'3%,89%S'$7*$.
8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.
9. Do not use an adapter to connect
this tool to a different outlet.
A&&7%?,2*$>%V,(8"83#
<&(%R&'(%S)8%?,2*$>%;*,9%C8#$('4$"&8%
D,8',7%X*2&(*%S/*(,$"83%A&&7
1. Remove all foreign objects, such as nails or metal
fragments, from the workpiece before planing.
2. Do not use to plane non-wood materials.
3. Do not plane workpieces shorter than 15", narrower
than 3/4", wider than 12-1/2" or less than 1/8" thick.
4. Blades are very sharp and are double-edged!
Wear heavy-duty leather work gloves at all times
when replacing, adjusting, or handling a blade.
5. Change both knives at once. Changing knives
individually could result in imbalance.
6. Do not unclog dust chute with
tool plugged in or blades moving.
Do not insert your finger into the dust chute.
7. Connect dust chute to bag or dust collection system
(not included) before use. Do not use without
a dust bag or dust collection system.
8. YS%ESA%ST6;@A6%VCAB%@ER%WF@;Y%
YC?@XG6YL%Y@D@W6YL%S;%;6DS!6Y1%%D&Z"83%
3',(9#%5'#$%5&Z*%2(**7>%,89%47&#*%"8#$,8$7>1
9. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.
10. When servicing use only identical replacement parts.
11. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
To Next Page
Loading...