Page 13<&(%$*4.8"4,7%K'*#$"&8#L%/7*,#*%4,77%HMNNNMNIIMOPQP1Item 63445
?@<6ARST6;@ACSED@CEA6E@EU6 ?6AFT
A(&'+7*#.&&$"83
V&(J/"*4*
T(&+7*5 T&##"+7*%U,'#*# G"J*7>%?&7'$"&8#
Deeper cut at
ends of board
(snipe).
1. Too little support of long boards.
2. Uneven force on cutter head.
1. Provide better support for long boards.
2. Level Tables according to G*Z*7"83%
A,+7*%6b$*8#"&8#%&8%/,3*%N1%
Torn, ragged,
rough or
raised grain.
1. Blades dull or damaged.
2. Cut is too heavy.
3. Blades cutting against grain.
4. Wood has a high moisture content.
1. Replace blades.
2. Reduce depth of cut.
3. Cut with grain.
4. Use dry wood.
T7,8*(
T(&+7*5 T&##"+7*%U,'#*# G"J*7>%?&7'$"&8#
Tool will not start. 1. Cord not connected.
2. No power at outlet.
3. Internal damage or wear. (Carbon
brushes or switch, for example.)
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Have qualified technician service tool.
Tool operates
slowly.
Extension cord too long or
wire size too small.
Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See A,+7*%@ on page 3.
Performance
decreases
over time.
1. Blades dull or damaged.
2. Carbon brushes worn or damaged.
1. Replace blades.
2. Have qualified technician replace brushes.
Roller case
adjustment
difficult
1. Sprockets and/or chain dirty.
2. Elevating screws and/
or columns dirty.
3. Elevating screws worn.
1. Clean and lubricate sprockets and/or chain.
2. Clean and lubricate elevating
screws and/or columns.
3. Replace elevating screws.
Chain jumping 1. Sprockets worn.
2. Chain worn.
1. Have sprockets replaced.
2. Have chain replaced.
Belt Slipping Loose belt Replace belt.
Excessive
dust in air
Leaking bag or loose connection. Check connections or replace collection bag.
Excessive noise
or rattling.
Internal damage or wear. (Carbon
brushes, bearings, or fan for example.)
Have qualified technician service tool.
Overheating/
Circuit breaker
tripping.
1. Dull blades.
2. Forcing boards through planer.
3. Blade dull or damaged.
4. Cut is too heavy.
5. Motor being strained by long or
small diameter extension cord.
1. Replace blades.
2. Allow auto feed to work at its own rate.
3. Replace blades.
4. Reduce depth of cut.
5. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See A,+7*%@ on page 3.
% <&77&)%,77%#,2*$>%/(*4,'$"&8#%).*8*Z*(%9",38&#"83%&(%#*(Z"4"83%$.*%$&&71%%%
Y"#4&88*4$%/&)*(%#'//7>%+*2&(*%#*(Z"4*1
To Next Page
Loading...