Page 13;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57656
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
P#*(?N,"8$*8,84*%L8#$('4$"&8#
GI%JK6!6MG%E6KLIPE%LM]PKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
G'(8%$.*%J&)*(%E)"$4.%&2%$.*%$&&7%&22=%'8/7'3%$.*%$&&7%2(&5%"$#%*7*4$("4,7%&'$7*$=%
#.'$%&22%$.*%),$*(%#'//7V%,89%#,2*7V%9"#4.,(3*%,77%(*#"9',7%),$*(%/(*##'(*%2(&5%
$.*%'8"$%+*2&(*%/*(2&(5"83%,8V%"8#/*4$"&8=%5,"8$*8,84*=%&(%47*,8"83%/(&4*9'(*#1
GI%JK6!6MG%E6KLIPE%LM]PKH%;KIN%GIIT%;FLTPK6-%
U&%8&$%'#*%9,5,3*9%*<'"/5*8$1%%L2%,+8&(5,7%8&"#*%&(%Z"+(,$"&8%
&44'(#=%.,Z*%$.*%/(&+7*5%4&((*4$*9%+*2&(*%2'($.*(%'#*1
O7*,8"83=%N,"8$*8,84*=%,89%T'+("4,$"&8
1. S6;IK6%6FOX%PE6= inspect the general
condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• damaged cord/electrical wiring,
• damaged high-pressure hose/accessories,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
2. F;G6K%PE6-%
• Drain water by tipping the unit.
Frost will damage the unit if it contains water.
• Flush Detergent Tank with water.
• Use only a clean cloth and mild detergent
to clean the body of the Pressure
Washer. Do not use solvents.
• Do not immerse any part of the tool in liquid.
• Dry off any remaining water
on all parts and fittings.
• Remove mineral deposits from the
nozzle using a thin, stiff wire brush.
3. J6KLIULOFTTH, remove mineral buildup.
Unplug the unit and lay it face down. Fill Water
Inlet with de-mineralizing solution, following
solution manufacturer's instructions. Drain
de-mineralizing solution out of Water Inlet
and rinse out inlet thoroughly before use.
4. QFKMLMR`%%GI%JK6!6MG%E6KLIPE%
LM]PKH-%%L2%$.*%#'//7V%4&(9%&(%R;OL%'8"$%&2%$."#%
/&)*(%$&&7%"#%9,5,3*9=%"$%5'#$%+*%(*/7,4*9%
&87V%+V%,%<',7"2"*9%#*(Z"4*%$*4.8"4",81
E$&(,3*%%
1. Place accessories, High-Pressure Hose and
Power Cord in their storage locations.
2. Store in a dry, frost-free room. Flush the unit with
automotive antifreeze prior to long-term storage.
Dispose of antifreeze according to local ordinances.