Bauer 20142E-B - Cleaning Procedures; Cleaning Windows; Cleaning Wood Surfaces; Cleaning Brick and Mortar

Page 12 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57656
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
O7*,8"83%Q"89&)#
a. Inspect caulking and/or glazing. Inspect trim.
UI%MIG%JK6EEPK6%QFEX%QLMUIQE%L;%
OFPTeLMR0RTFfLMR0GKLN%LE%MIG%LMGFOG1
b. If needed, apply detergent according
to manufacturer's instructions.
c. Set Nozzle to low-impact fan spray.
UI%MIG%PE6%XLRX?LNJFOG%EJKFH=%
;IKO6%NFH%SK6Fe%RTFEE1
d. Point Spray Gun at 45° angle to, and 4 feet
away from, window. Spray window.
O7*,8"83%Q&&9
UI%MIG%OT6FM%QIIU%GXFG%LE%
XIG%IK%LM%ULK6OG%EPMTLRXG1
a. If needed, apply wood cleaning
detergent according to manufacturer's
instructions. For vertical surfaces,
apply detergent from bottom to top.
b. Scrub stained areas as needed.
c. Set Nozzle to low-impact fan spray.
d. Point Spray Gun at 45°. Spray surface,
working with the grain of the wood.
e. Let surface dry completely, then apply
stain or sealer, as needed, according
to manufacturer's instructions.
O7*,8"83%S("4^%,89%N&($,(
a. Inspect mortar, patching as needed. Let mortar
cure according to manufacturer's instructions.
b. Soak surface prior to applying detergent.
c. If needed, apply brick cleaning
detergent according to manufacturer's
instructions. For vertical surfaces,
apply detergent from bottom to top.
d. Scrub stained areas as needed.
e. Set Nozzle to low-impact fan spray.
GI%JK6!6MG%UFNFR6=%IMTH%
PE6%TIQ?LNJFOG%E6GGLMR1
f. Point Spray Gun at 45°. Spray surface.
g. Let surface dry completely, then
apply sealer, as needed, according to
manufacturer's instructions as needed.
8. When finished:
• Release Trigger, then set Trigger Safety Lock.
• Turn off Power Switch.
• Turn off water supply.
• Unplug the unit.
• Point Nozzle in safe direction, press Trigger
to release all pressure, then release Trigger.
• Disconnect water supply hose.
• Disconnect High-Pressure Hose from unit.
• Disconnect High-Pressure
Hose from Spray Gun.
9. LNJIKGFMG-%%OT6FM%GX6%MIffT6E%F;G6K%
6!6KH%PE6%GI%NFLMGFLM%EJKFHLMR%
JIQ6K%FMU%JK6!6MG%JPNJ%UFNFR61
• Remove Wand from Spray Gun.
• Remove Nozzle from Wand by
turning Nozzle clockwise.
• Push Nozzle Tip Cleaner into tip to
push out debris and buildup.
• Remove Nozzle Tip Cleaner and
back-flush water through Nozzle.
• Reattach Nozzle to Wand.
• Clean and store according to
P#*(?N,"8$*8,84*%L8#$('4$"&8#%&8%/,3*%>g1