Bayco 2134 - User Manual

To Next Page

Operating Instructions for

Model 2134 Work Light

Rechargeable Floodlight - Spotlight

INS-2134-15

CAUTION: Do not use this work light in explosive atmospheres, near flammable liquids,

or where explosion-proof lamps are required. Do not immerse in water.

CAUTION: For light duty work only.

Thank you for purchasing this Bayco work light. Save these instructions.

Please read these instructions before using your work light. Be sure to charge the work

light before the first use.

CHARGING

Initial Use

Fully charge the work light before the first use. If the battery is new or has been unused

for several months, several charge and discharge cycles may be needed to reach full

battery capacity. To reach maximum performance, run the light to completely discharge

the battery and then recharge. Each charge cycle will extend the operation time until

maximum capacity is achieved. The charge time for maximum capacity is approximately

8 hours.

Regular Use

Use only the supplied AC charging adapter.

 For best performance, charge the work light when the LED’s start to dim.

 Connect the AC power adapter to the light. The red indicator will light.

 The red light indicates the work light is being charged. The red light remains on until

the battery is fully charged. At full charge, the light turns off. The total time to full

charge varies depending on the remaining charge in the battery pack.

 Keep the work light plugged into the charger to maintain a trickle charge.

SAFETY

CAUTION BRIGHT LED RADIATION: AVOID DIRECT EYE EXPOSURE. The light is a

Class 2 LED product per IEC 60825-1 Edition 1.2.2001.

 Do not use or charge this work light in explosive or hazardous areas.

 Do not attempt to repair or disassemble the work light or the charger power supply.

 Use only the supplied AC charger.

TIPS TO EXTEND BATTERY LIFE

The work light NiMH internal battery pack does not have a memory effect. Charging the

work light often helps extend its useful life.

 A new work light or one that has not been used for a long period of time may not

accept a full charge initially. This is normal and does not indicate a problem. Fully

discharge and then charge the unit several times to condition the battery pack for full

capacity. As the battery pack capacity increases the charge time shortens.

 Charge the unit after each use, whether the work light is fully discharged or not.

 Store the work light at room temperature

OPERATION FOR 2134

The work light has a 2 position rocker switch to activate either the floodlight or spotlight.

The center position turns the light off. The magnetic hook can be placed on the top of the

light or the side.

WARRANTY

PRODUCTS COVERED UNDER THIS LIMITED WARRANTY:

This product is warranted to the original purchaser for 1 year and only covers failures due

to defects in materials or workmanship. If this product is used for rental purposes, the

warranty term is reduced to 90 days from the date of purchase.

NOT COVERED

The warranty does not cover normal wear and tear or cosmetic damage. The Limited

Warranty also does not cover damages which occurred in shipment or failures which are

caused by accidents, misuse, abuse, faulty installation and lightning damage.

Consequential damages, incidental damages or incidental expenses, including damage

to property. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply to you. This

warranty gives you specific legal rights, which may vary from state to state. This warranty

does not apply to certain Bayco professional products that carry a specific warranty

unique to those products.

WARRANTY CLAIMS - USA

Contact Bayco for USA warranty claims. Call and Bayco Customer Service will provide

a Return Goods Authorization (RGA) to facilitate rapid warranty action. After receiving

the RGA, send the product (shipping prepaid) to BAYCO. Include a dated proof of

purchase and a brief description of the defect with your name, address and phone

number. Your product will either be repaired or replaced at the option of Bayco and

returned as soon as practical, but no later than 45 days after being received by Bayco.

WARRANTY CLAIMS - CANADA

Return the product to the place where purchased with a dated proof of purchase and a

brief description of the defect with your name, address and phone number. Your product

will either be replaced or purchase price refunded.

Other manuals for Bayco 2134

Instruction Manual2 pages

Need help?

Do you have a question about the Bayco 2134 and is the answer not in the manual?

Summary

Operating Instructions

Charging

Instructions for charging the work light, including initial use and regular charging practices.

Safety Precautions

Essential safety warnings, including avoiding direct eye exposure to bright LED radiation.

Battery Life Tips

Guidance on extending the NiMH battery pack's useful life and maintaining capacity.

Operation

Details on how to operate the work light, including switch functions and magnetic hook placement.

Warranty Coverage

Information on what is covered and not covered under the limited warranty for the product.

Bayco Products Limited 1-Year Warranty

Warranty Claims - USA

Procedure for submitting warranty claims within the USA, including RGA requirements.

Warranty Claims - Outside of USA

Instructions for returning the product for warranty claims outside of the USA.

Extent of Covered Warranty Work

Details on how Bayco will handle warranty work, including repair or replacement options.

Warranty Questions

Contact information for Bayco Customer Service regarding warranty inquiries.

Declaration of Conformity

Description of Equipment

Identifies the product as a rechargeable work light compliant with EU RoHS directive.

This document provides operating instructions for the Bayco Model 2134 Work Light, a rechargeable floodlight and spotlight designed for general work applications. It emphasizes safe and effective use, charging procedures, and warranty information.

Function Description

The Bayco Model 2134 Work Light is a versatile illumination tool offering both floodlight and spotlight functions. It is designed to provide portable lighting for various tasks, powered by an internal rechargeable battery. The device is intended for light-duty work and is not suitable for use in explosive atmospheres or near flammable liquids. Its primary function is to deliver reliable light output in situations where a portable, rechargeable source is required. The work light is equipped with LED technology, ensuring efficient illumination.

Usage Features

The work light features a straightforward operation with a 2-position rocker switch that allows users to select between floodlight and spotlight modes. The center position of the switch turns the light off. This dual-mode functionality provides flexibility, enabling users to choose the appropriate beam pattern for their specific task, whether it requires a broad area illumination (floodlight) or a more focused beam (spotlight).

For convenience, the work light includes a magnetic hook. This hook can be positioned on either the top or the side of the light, allowing for hands-free operation by attaching the light to metallic surfaces. This feature enhances the usability of the device in various work environments where stable positioning is beneficial.

The charging process is designed for ease of use. The work light should be fully charged before its initial use. For optimal battery performance, especially with a new battery or one that has been unused for several months, several charge and discharge cycles may be necessary to reach full battery capacity. To achieve maximum performance, users are advised to completely discharge the battery and then recharge it. Each such cycle contributes to extending the operation time until maximum capacity is reached, which is approximately 8 hours.

Regular charging involves connecting the supplied AC power adapter to the light. A red indicator light will illuminate, signifying that the work light is charging. This red light remains on until the battery is fully charged, at which point it turns off. The total time required for a full charge varies depending on the remaining charge in the battery pack. To maintain a trickle charge and ensure the light is always ready for use, it can be kept plugged into the charger.

Safety is a key aspect of the work light's design and usage. Users are cautioned against direct eye exposure to the bright LED radiation, as it is a Class 2 LED product. The device should not be used or charged in explosive or hazardous areas. Furthermore, users are explicitly warned not to attempt to repair or disassemble the work light or its charger power supply, and to use only the supplied charger. These precautions are critical for ensuring user safety and maintaining the integrity of the device.

Maintenance Features

The Bayco Model 2134 Work Light incorporates a NiMH internal battery pack, which is designed to be free from memory effect. This characteristic simplifies battery maintenance, as charging the work light often helps extend its useful life without concerns about reducing battery capacity due to incomplete discharge cycles.

To maximize battery life and performance, several maintenance practices are recommended. For a new work light or one that has been unused for a long period, it may not accept a full charge initially. This is considered normal and not an indication of a problem. In such cases, fully discharging and then charging the unit several times will condition the battery pack to achieve full capacity. As the battery pack capacity increases through these conditioning cycles, the charge time will gradually shorten.

It is also recommended to charge the unit after each use, regardless of whether the work light has been fully discharged or not. This practice helps maintain the battery in an optimal state, ensuring it is ready for subsequent use. Storing the work light at room temperature is advised to further support battery longevity and overall device health.

The product is covered by a limited warranty, which addresses failures due to defects in materials or workmanship for one year for the original purchaser. This warranty includes the LEDs, housing, lenses, electronics, switches, rechargeable batteries, and chargers. Bulbs (other than LEDs) are covered for 90 days. Disposable non-rechargeable batteries are excluded. The warranty does not cover normal wear and tear, cosmetic damage, or failures caused by accidents, misuse, abuse, faulty installation, or lightning damage. For warranty claims in the USA, customers are instructed to contact Bayco Customer Service to obtain a Return Goods Authorization (RGA) before sending the product. The product will either be repaired or replaced at Bayco's option. For warranty claims outside of the USA, the product should be returned to the place of purchase. If the product is used for rental purposes, the warranty term is reduced to 90 days. This comprehensive warranty and maintenance guidance aim to ensure the long-term functionality and reliability of the Bayco Model 2134 Work Light.