EasyManua.ls Logo

BE HK045F - User Manual

BE HK045F
18 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model Numbers
HK045F / HK070F / HK125FW /
HK175FW / HK215FW
© 2020 BAR Group Pty Ltd
Head Office
15 Hudson Place
Mulgrave NSW 2756, Sydney
Users Manual &
Operating Instructions
CONSUMER: READ AND SAVE THESE INSTRUCTIONS
GENERAL HAZARD WARNING:
READ AND UNDERSTAND ALL OF THE INSTRUCTIONS IN THIS MANUAL
BEFORE ASSEMBLING, STARTING, OR SERVICING THE HEATER. Be sure to comply with the
instructions and warnings provided with this heater. Failure to comply can result in fire or explosion
that can cause property loss, bodily injury, or loss of life. Only persons who can follow and
understand these instructions should operate or service this heater.
DANGER
NOT FOR USE IN RESIDENTIAL LIVING AREAS OR IN ENCLOSED SPACES
WITHOUT ADEQUATE VENTILATION. INDOOR USE PERMITTED ONLY FOR
THE TEMPORARY HEATING OF BUILDINGS OR STRUCTURES UNDER CONSTRUCTION,
ALTERATION OR REPAIR. This is an unvented portable heater that uses air (Oxygen) from within
the area in which it is used. Failure to provide adequate combustion and ventilation air will result in
asphyxiation, carbon monoxide poisoning, bodily injury or death. Refer to “Ventilation” on Page 7.
DANGER
This appliance shall be installed in accordance with the rules in force,
and used only in sufficiently ventilated space. Consult instructions before
installation and use of this appliance.
WARNING
FACTORY ID: 500
BPKI-400
HK070F
HK125FW
HK175FW HK215FW

Questions and Answers

  • J
    James DawsonAug 11, 2025
    What to do if my BE HK045F fires, but shuts off quickly and shows “E1”?
    • M
      Melissa JonesAug 11, 2025
      If your BE Heater fires but then shuts off and displays “E1”, several issues could be the cause: * Incorrect pump pressure: Adjust the pump pressure. * Dirty filters: Clean or replace the air and fuel filters. * Dirty nozzle: Clean or replace the nozzle. * Dirty or defective photocell: Clean, replace, or adjust the photocell position. If the photocell is defective, replace it. * Wiring: Check the wiring connections between the Main PCB and the photocell.
  • M
    Michele KellyAug 17, 2025
    What to do if my BE HK045F Heater will not operate and shows error code E1?
    • J
      Jeffery SotoAug 17, 2025
      If your BE Heater isn't operating and displays error code “E1”, consider these potential causes: * Fuel: Ensure the fuel tank has fresh kerosene. * Pump pressure: Adjust the pump pressure. * Spark plug: Clean or replace the spark plug. * Fuel filter or nozzle: Clean or replace these components. * Fuel contamination: Rinse the fuel tank with clean kerosene. * Electrical connections: Inspect the electrical connections between the transformer and circuit board and re-attach the igniter wire to the spark plug, if it is not connected. * Igniter: Replace the igniter if it is defective.
  • L
    Lisa WilsonAug 23, 2025
    What to do if my BE HK045F Heater fan is not working?
    • J
      Jason DanielAug 23, 2025
      If the fan on your BE Heater isn't working, consider the following: * Thermostat setting: Increase the thermostat setting. * Electrical connections: Check the electrical connections between the Main PCB and the motor. Consult the wiring diagrams for guidance.
  • S
    smithdanielleAug 28, 2025
    How to fix a BE HK045F that does not turn on?
    • G
      Gina MendozaAug 28, 2025
      If your BE Heater isn't turning on, try the following: * Overheated sensor: Turn the power off and let the heater cool for 10 minutes, then turn it back on. * Power supply: Check the power cord and extension cord to ensure they are properly connected, and test the power supply. * Fuse: Check and replace the fuse if necessary. * Temperature Limit Sensor: Inspect the electrical connection between the Temperature Limit Sensor and Circuit Board. See Wiring Diagrams.
  • C
    Christopher RogersSep 3, 2025
    Why does my BE HK045F Heater produce excess soot?
    • Z
      Zachary MooreSep 3, 2025
      Excess soot from your BE Heater could be due to: * Dirty air or fuel filters: Try cleaning or replacing them. * Poor fuel quality: Ensure the fuel is not contaminated or old. * Incorrect pressure: Make sure that you are using the proper pressure.

BE HK045F Specifications

General IconGeneral
BrandBE
ModelHK045F
CategoryHeater
LanguageEnglish

Related product manuals