To Next PageTo Next Page
Need help?Do you have a question about the Beechcraft Turbo-Baron 56TC and is the answer not in the manual?
Details of revisions made to the manual, including issue and insertion dates.
Log of temporary revisions applied to specific sections or pages of the manual.
Identifies all pages that are currently in effect within the manual.
An alphabetical listing of topics covered in the manual for quick reference.
Details on the aircraft engine, including specifications and operating parameters.
Covers various specifications not fitting into other categories, like aircraft dimensions.
Provides key physical measurements of the aircraft, including length, span, and height.
Lists publications provided by vendors for various aircraft components.
References for engine overhaul manuals and parts catalogs.
Manuals related to the aircraft's fuel injection system operation and service.
Documents for propeller overhaul, maintenance, and governor adjustments.
Information on battery maintenance, servicing, and handling precautions.
Details on the installation, maintenance, and troubleshooting of strobe lighting systems.
Procedures for the electrically heated propeller deicer system, including boot maintenance.
Maintenance instructions for the surface deicer system, focusing on filter inspection.
Overhaul instructions for the heater vent blower assembly.
Maintenance instructions for the aircraft heater and ignition unit.
Manuals and procedures for the air conditioner compressor.
Specifies the minimum allowable thickness for brake discs and linings.
Procedure for adjusting the parking brake system linkage.
Instructions for bleeding the brake system using gravity or pressure methods.
Procedures for rigging the autopilot control systems, including aileron, elevator, and rudder.
General information on maintaining and repairing the autopilot system.
Proper procedures for towing the aircraft, including towbar attachment.
Guidelines for securing the aircraft for mooring, including using tie-down points.
Instructions on how to set and adjust the parking brake system.
Procedures for safely jacking the aircraft for maintenance.
Instructions on how to hoist the aircraft for maintenance or parts replacement.
Steps for safely removing fuel from the aircraft's system.
Procedure for adjusting the fuel pressure of the engine-driven fuel pump.
Detailed steps for removing and installing the nacelle fuel cell.
Procedures for removing and installing fuel cells in the leading edge.
Methods for testing the oxygen system for leaks.
Procedure for purging the oxygen system to remove odors or contamination.
Instructions on how to safely replace an oxygen cylinder.
Procedures for minor repairs to propeller blades, including nick and gouge dressing.
Steps for removing the propeller accumulator assembly.
Guidelines for minor repairs to propeller blades by approved personnel.
Diagrams and lists identifying access points on the fuselage and empennage.
Illustrations showing locations of access openings on the aircraft wings.
Procedures for removing the wing tip section, including deicer boot removal.
Steps for installing the wing tip, including electrical connections.
Detailed instructions for safely removing a wing from the aircraft.
Procedures for installing a wing, including alignment and bolt torquing.
Revised procedures for connecting flap drive cables to the flap drive motor.
Steps for removing the flap from the aircraft.
Procedure for installing the flap, including rollers and bolts.
Instructions for installing flap track rollers in the flap track brackets.
Adjusting flap limit switches and rigging the control system for proper travel.
Procedure for adjusting the flap position indicator transmitter.
Steps for removing and installing the flap motor assembly.
Procedures for the overhaul of the flap motor gearbox.
Specifications for flap positions during approach and full down configurations.
Procedures for rigging the autopilot control systems for ailerons, elevator, and rudder.
References for autopilot maintenance, repair, troubleshooting, and testing procedures.
Specifies the minimum allowable thickness for brake discs and linings.
Procedure for adjusting the parking brake system linkage.
Instructions for bleeding the brake system using gravity or pressure methods.
Description of the optional landing gear safety system functions.
Procedures for maintaining and adjusting the landing gear safety system.
Steps to check the safety switch system's function in the test position.
Procedure for adjusting the microswitch for proper operation.
Procedure for rigging the landing gear mechanism and doors when removed or disconnected.
Detailed steps for disassembling the main landing gear shock strut.
Guidelines for inspecting strut components and replacing worn or defective parts.
Manufacturing tolerances for nose gear components to determine wear extent.
Procedures for removing and installing the nose gear assembly.
Instructions for the overhaul of the nose gear shimmy dampener.
Procedure to adjust the travel stop for the nose wheel.
Troubleshooting for the pitot and static pressure system.
Troubleshooting procedures for the stall warning system.
Procedure for adjusting suction relief valves in conjunction with the autopilot.
Steps for removing and installing the dry air vacuum pump.
Procedures for adjusting pressure regulators and related components.
Inspection and adjustment procedures for the pressure system with deicer and autopilot.
Procedures for preparing and painting aluminum surfaces.
Steps for repairing urethane paint finishes, including stripping and application.
Guidelines for replacing various electrical components.
Information on nickel-cadmium batteries, including electrolyte adjustment.
Procedures for adjusting voltage regulators for alternator systems.
Instructions for adjusting the overvoltage relay when the aircraft circuit is not accessible.
Functional checks for overvoltage relays and voltage regulators.
Adjusting voltage regulators and paralleling rheostats for equal generator output.
Procedures for performing final checks after paralleling generators.
Steps for safely removing the generator from the aircraft.
Procedure for removing the starter motor from the aircraft.
Troubleshooting specific to the Bullock unit for strobe lights.
Troubleshooting steps for alternator failure to charge.
Diagnosis and remedies for noise issues with the alternator.
Troubleshooting steps for loadmeter or light flickering issues.
Troubleshooting steps when no power is indicated with the battery master switch ON.
Troubleshooting steps for zero or low charge indication from the generator.
Diagnostic steps for instances where the generator has no output.
Procedures for addressing low output from the generator.
Overhaul or replacement intervals for landing gear components.
Overhaul or replacement intervals for engine and related components.
Overhaul or replacement intervals for flaps and flight control systems.
Overhaul or replacement intervals for fuel system components.
Overhaul or replacement intervals for various aircraft instruments.
Overhaul or replacement intervals for electrical system components.
Overhaul or replacement intervals for utility systems like heaters and air conditioners.
Overhaul or replacement intervals for miscellaneous aircraft parts.
Notes on specific conditions that may require more frequent inspections.
Inspection items related to the engine and its systems.
Inspection items related to the aircraft structure and exterior.
Inspection points for the landing gear system.
Inspection items related to the aircraft cabin and its components.
Inspection procedures for the electric propeller deicer system.
General| Brand | Beechcraft |
|---|---|
| Model | Turbo-Baron 56TC |
| Category | Tools |
| Language | English |
