To Next PageTo Next PageWhy is my Beem G-1030ST-E-CERAMIC Iron not producing steam?
Several factors could be preventing your Beem Iron from producing steam. First, ensure that the steam generator is switched on. Also, check that the filter is correctly inserted in the water tank and that the tank has enough water. If the water tank is not correctly inserted into the steam generator, you should re-insert it until you hear it click.
What to do if my Beem G-1030ST-E-CERAMIC Iron stays cold?
If your Beem Iron is staying cold, first ensure that the appliance is switched on using the on/off switch located on the steam generator. Also, check the temperature setting; if it's set to '•', adjust it to the required temperature.
What to do if water drips from the sole of my Beem G-1030ST-E-CERAMIC?
If water is dripping from the sole of your Beem Iron, it could be due to a couple of reasons. If you've been pressing the steam pressure button for too long and the Heat indicator on the steam generator lights up, wait for the iron to reheat until the Heat indicator goes out. If that doesn't work, try briefly selecting a lower steam volume. Also, ensure that the iron's temperature is not set to off (position •) or too low (position Synthetic). For steam ironing, you need to select at least level Wool/Silk or a higher temperature.
Why does limescale emerge from the steam nozzles of my Beem G-1030ST-E-CERAMIC Iron?
Limescale emerging from the steam nozzles of your Beem Iron is likely due to hard water or infrequent descaling. You may need to change the anti-limescale cartridge if it is used up.
What to do if all lamps on my Beem Iron go out?
If all the lamps on your Beem Iron go out, it likely means the appliance has switched off automatically. Simply press the on/off button to switch the appliance back on.
Why won't my Beem G-1030ST-E-CERAMIC switch on?
If your Beem Iron won't switch on, make sure the mains plug is properly plugged in and that the socket or house fuse is working correctly.
What to do if my Beem G-1030ST-E-CERAMIC has no steam and the pump indicator light goes off?
If your Beem Iron has no steam and the pump indicator light goes off when you press the steam button, the steam chamber may not have heated up yet. Wait until the Heat indicator goes out. Also, check that the steam volume regulator is not set to off. Press the button of the steam volume regulator until one of the three steam symbols lights up.
Why does the fuse blow when I use my Beem G-1030ST-E-CERAMIC Iron?
If the fuse blows when you use your Beem Iron, it could be due to a defect in the appliance or too many devices being connected to the same circuit. Reduce the number of appliances using the circuit.
How to tell if my Beem G-1030ST-E-CERAMIC Iron has reached the necessary temperature?
Wait until the temperature control lamp on the Beem Iron no longer flashes.
Covers intended use, child safety, electrical risks, burn/fire hazards, and general injury prevention.
Explains auto-off, anti-drip system, ceramic sole care, and temperature setting.
Guides on preparing the utensil, setting steam volume and temperature, and starting ironing.
Explains suitability for hanging items, setting maximum steam, and technique for removing creases.
Lists common faults, possible reasons, and remedies for the steam iron.
Stresses cooling down, avoiding immersion in water, and using non-abrasive cleaners.
General| Type | Steam Iron |
|---|---|
| Model | G-1030ST-E-CERAMIC |
| Water Tank Capacity | 300 ml |
| Soleplate Material | Ceramic |
| Vertical Steam | Yes |
| Anti-Drip System | Yes |
| Self-Cleaning Function | Yes |
| Steam Boost | 150 g/min |
| Auto Shut-off | Yes |
| Voltage | 220-240 V |
| Frequency | 50 Hz |
