Behringer VIRTUALIZER 3D FX2000 Manual

Page 3 of 4
• ULTRA BASS – sub-harmonic processor
combined with bass exciter and limiter
• STEREO IMAGER – divides the signal
into middle and side signals, allowing
individual signals to be amplied when
desired and placed on the stereo image
• ULTRA WIDE – creates a broader
stereo image
• BINAURALIZER – also creates a broader
stereo image and compensates for
crosstalk between both speakers
Filter/EQ FX:
• AUTO FILTER – inuences the frequency
response of a signal: Three lter types in
dierent variations are included: low pass,
band pass and high pass
• LFO FILTER – similar to the auto lter
algorithm, but modulated by an
oscillator with dierent wave types and
speed adjust
• PARAMETRIC EQ – allows you to control
the bandwidth, frequency and amplitude
of a signal
• GRAPHIC EQ – the sound spectrum is
divided into six (6) adjacent frequency
bands, which can be cut or boosted,
bandwidth is predetermined
Distortion FX and Amp Simulations
The FX2000 is also equipped with
distortion, amplier and speaker
simulation including VOCAL DISTORTION,
TUBE DISTORTION, GUITAR AMP, TRI FUZZ,
SPEAKER SIMULATION, RING MODULATOR
and LO-FI.
Special FX:
• VINYLIZER – adds clicks and/or noise to
the signal, reminiscent of old vinyl records
and tape machines
• SAMPLER – allows you to record and
playback up to ve (5) seconds of
program material
Continued on next page
LEVEL METERS display
signal level relative to
setting of OPERATING LEVEL
button on rear panel
DISPLAY shows eect
name, parameter
name, and parameter
value of current preset
Front Panel
Rear Panel
MIX knob adjusts
wet/dry mix of
output signal
EFFECT button enables
JOG WHEEL to scroll
through 71 basic
eect algorithms
PRESET button
enables JOG WHEEL
to scroll through
200 presets
SETUP button enters
Setup Mode, enabling
EDIT KNOBS to select
categories within MIDI,
INPUT, OUTPUT, and
CONFIGURATION
EDIT button selects
function and LEDs
indicate active function
COMPARE button
temporarily
restores altered
preset’s settings
for comparison to
original sound
JOG WHEEL scrolls
through presets
and adjusts
parameter values
POWER button
STORE button saves
altered preset to
desired location
STATUS LEDs
indicate type of
value ready for edit
EFFECT GROUP LEDs
indicate category of
current eect
EDIT KNOBS adjust
various eect parameters,
EQ settings, MIDI functions and
INPUT/ OUTPUT congurations
EDIT LEDs indicate which
parameters are adjusted
by the EDIT KNOBS
MIDI IN, MIDI OUT, and MIDI
THRU connectors transmit
and receive MIDI commands
INPUT and OUTPUT connections
are available as balanced
¼" TRS and XLR jacks
OPERATING LEVEL button
switches between
-10 dBV and +4 dBu
VIRTUALIZER 3D
FX2000

Behringer VIRTUALIZER 3D FX2000 Specifications

Analog Inputs and Outputs

input connectors	XLR and ¼" TRS
input impedance	80 kΩ balanced
output connectors	XLR and ¼" TRS

Power

voltage USA/Canada	120 V~, 60 Hz
voltage Europe/U.K./Australia	230 V~, 50 Hz
power consumption	15 Watts max.

System Specifications

bandwidth	20 Hz to 20 kHz, +/- 3 dB
SNR	91 dB, unweighted, 20 Hz to 20 kHz
THD	0.018 % typ. @ +4 dBu, 1 kHz, 0 dBu input, gain 1

Weight and Dimensions

dimensions	8.54 x 1.75 x 19.01" (217 x 44.5 x 483 mm)
net weight	4.18 lbs / 1.9 kg