Behringer XENYX QX1832USB User Manual

18
XENYX QX1832USB/QX1222USB
XENYX QX1832USB/QX1222USB Controls
(1) USB wireless input accepts a USB
receiver for use with Behringer ULM
wireless microphones.
(2) GAIN knob adjusts the sensitivity of the MIC
and/or LINE inputs.
(3) COMP knob adjusts the amount of
compression eect on the channel.
(4) EQ knobs adjust the high, mid and low
frequencies of the channel. Adjust the FREQ
knob on the QX1832USB to select the specic
frequency adjusted by the MID knob.
(5) MON knob adjusts how much of the channel’s
signal routes to the MON SEND/OUT jack.
(6) AUX 1 knob (QX1832USB only) adjusts how
much of the channel’s signal routes to the
AUX 1 jack. Press the PRE button when using
AUX 1 as an extra monitor send.
(7) FX knob adjusts how much of the channel’s
signal routes to the internal multi-FX
processor or the AUX SEND 2/FX SEND jack.
(8) PAN/BAL knob positions the channel in the
stereo eld.
(9) MUTE button mutes the channel.
(10) CLIP LED lights when the channel
signal overloads.
(11) CHANNEL FADER adjusts the channel volume.
(12) MULTI-FX PROCESSOR adds a selected sound
eect to any channels whose FX knob is
turned up. See the Multi-FX Processor section
for details.
(13) FX SEND knob/fader adjusts the amount of
signal sent to the internal multi-FX processor
or an external eects processor via the
FX SEND jack.
(14) GRAPHIC EQ adjusts specic frequencies in
the sound spectrum.
(15) XPQ SURROUND knob adjusts the amount
of stereo enhancement on the mix. Press the
XPQ TO MAIN button to activate the eect.
(16) VU METER displays the MAIN OUTPUT
signal level.
(17) PHONES/CTRL ROOM knob adjusts
the headphone or studio monitor
(QX1832USB) volume.
(18) VOICE CANCELLER button lters out vocal
frequencies from audio plugged into the
2-TRACK INPUT, enabling your mixer to act as a
karaoke machine.
(19) MODE button (QX1832USB only) determines
whether the channels’ SOLO button operates
as ‘Solo in Place’ (button out) or ‘Pre-Fader
Listen’ (button in). PFL is preferred for gain
setting purposes.
(20) MON SEND fader adjusts the amount of
signal sent to a monitor speaker via the
MON OUT jack.
(21) FX/AUX2 RET fader (QX1832USB only)
adjusts the amount of internal or external
eects included in the mix.
(22) SUB 1-2 faders (QX1832USB only) adjust the
output of the SUB OUTPUT jacks.
(23) MAIN MIX faders adjust the overall output of
the mixer.
(24) SOURCE buttons (QX1832USB only) route the
USB/2-TR, SUB 1-2, and MAIN MIX to the
PHONES and CONTROL ROOM jacks.
(25) FX TO MON and FX TO MAIN knobs
(QX1222USB only) adjust the amount of signal
from the internal multi-FX processor or an
external eects processor that is included in
the main or monitor mix.
(26) STANDBY button (QX1222USB only) mutes all
microphone channels.
(27) USB/2-TR RTN fader (QX1222USB only)
adjusts the level of the 2-track RCA inputs or
USB input.
(28) AC IN accepts the included power cable for
connection to a mains outlet.
(29) POWER ON switch turns the mixer on and o.
(30) PHANTOM ON switch sends 48 V to the XLR
inputs for use with condenser microphones.
(31) LOW CUT button eliminates unwanted low
frequencies from the channel.
(32) AUX 1 SEND knob (QX1832USB) adjusts the
level of the AUX 1 signal sent to an eects
processor or monitor speaker.
(33) AUX 1 RETURN knob (QX1832USB) adjusts the
level of the signal returning from an eects
processor to the AUX 1 RETURN jacks.
(34) USB/2-TR TO MAIN button (QX1832USB)
routes the USB and 2-Track playback to the
MAIN MIX and mutes the USB/2-TR OUT
recording signal.
(35) LEVEL SET LED (QX1222USB only) is used for
setting the correct input level of the channel.
See the Gain Setting section for more details.
(EN) Step 2: Controls

Behringer XENYX QX1832USB Specifications

General

Brand	Behringer
Model	XENYX QX1832USB
Category	Music Mixer
Language	English