Why is the sound system not working on my Beka Hospitec AVERO Phoenix Medical Equipment?
If the sound system on your Beka Hospitec Medical Equipment isn't working, verify that the USB stick is correctly inserted and that it is not defective. If it is, try inserting a new USB stick.
Why does my Beka Hospitec AVERO Phoenix Medical Equipment shut off during lifting?
If the drive of your Beka Hospitec Medical Equipment is switched off during the lifting procedure, it might be because the maximum load (maximum patient weight) has been exceeded.
Why is my Beka Hospitec AVERO Phoenix Medical Equipment stuck in the up position?
If the lifting bath tub of your Beka Hospitec Medical Equipment remains in the top end position, check if the mains voltage is present.
Why is only hot or cold water coming out of my Beka Hospitec AVERO Phoenix faucet?
If you find that only hot or cold water is flowing from the faucet of your Beka Hospitec Medical Equipment, consider these checks: * Examine the water supply. * Verify that the hot and cold-water connections are not reversed. * Inspect the filter, as well as the inlet and outlet faucet, for any clogging.
How to increase water flow rate in my Beka Hospitec Medical Equipment?
To address a low water flow rate in your Beka Hospitec Medical Equipment, you can: * Check the water supply. * Check the filter, as well as the inlet and outlet faucet, for clogging. * Ensure that the flow rate is sufficient for the supply conditions. * Check if the connecting hoses are bent.
How to fix a leaking faucet on Beka Hospitec AVERO Phoenix Medical Equipment?
If the faucet on your Beka Hospitec Medical Equipment is leaking water, check the seals for damage and replace them if necessary.
Why are the lights off on my Beka Hospitec AVERO Phoenix Medical Equipment?
If the mains LED and temperature indications on your Beka Hospitec Medical Equipment do not light up, verify that the fuse and the fault-current circuit breaker are activated.
Why is there no water coming from my Beka Hospitec AVERO Phoenix?
If there's no water coming out of your Beka Hospitec Medical Equipment, here’s what you can check: * Ensure that the shut-off valves of the cold and hot water are open. * Inspect the filter located in the water inlet.
How to reduce filling speed on Beka Hospitec Medical Equipment?
If the water pressure is too high and causing a high filling speed in your Beka Hospitec Medical Equipment, install a pressure reducer on site.
What to do if the mains voltage fails on Beka Hospitec AVERO Phoenix Medical Equipment?
If the mains voltage fails on your Beka Hospitec Medical Equipment, you can: * Check the fuse. * Check the cables for damages.
Expresses gratitude for trust and highlights quality criteria in product manufacturing and testing.
Provides contact details including name, address, phone, fax, and email for BEKA Hospitec GmbH.
Details BEKA Hospitec GmbH's certification according to DIN EN ISO 13485 by TÜV SÜD.
Emphasizes the importance of reading the manual and safety instructions for proper and safe device functioning.
Outlines the manufacturer's limitations of liability for improper use and warranty conditions for modifications or unauthorized parts.
States the manual contains essential information for product operation, including descriptions, illustrations, and cleaning/disassembly.
Describes the location and content of the product's type plate, including serial number and technical specifications.
Defines the product name as "lifting bath tub" or "(bath) tub" for use within the manual.
Specifies the product is designed for patient bathing and care in hospitals/care centers by trained nurses.
Mentions compliance with VDE prescriptions and advises checking electrical installation compliance with local regulations.
Stresses the imperative observance of all notes, specifications, and warnings for safe operation and liability.
Lists and explains various safety symbols and their meanings, including CE, IPX4, and protective conductor class.
Details critical warnings regarding operation by trained staff, environmental conditions, load limits, and user precautions.
Provides instructions for safely removing packaging materials and securing the product during transport.
Details requirements for connecting the bath tub to the power supply network, including socket type and cable specifications.
Emphasizes the importance of a quality protective conductor for Class I equipment and compliance with national regulations.
Guides on initial setup, including manual checks for water temperature, mixer setup, and optional disinfecting units.
Explains the functions of various buttons and displays on the control keypad for bath tub operation.
Describes how to adjust the bath tub's height using the "Up" and "Down" buttons on the keypad.
Details the operation of the hand shower, including automatic shut-off and scalding protection features.
Explains how to use buttons for automatic water filling to predefined heights and manual filling procedures.
Describes the temperature display format and the "HOT" message indication for high temperatures.
Explains how to activate and deactivate the disinfection system using the "DIS" button.
Refers to additional user manuals for optional features like disinfection, light therapy, sound, and aromatherapy systems.
Instructs the user to check the system's condition and functional safety before commencing operation.
Covers filling the tub, patient positioning, draining, and post-operation cleaning/disinfection.
Provides guidance on cleaning the bath tub using soft cloths and mild cleaning agents, avoiding abrasives.
Details the procedure for disinfecting the bath tub after each use to prevent transmission and infection.
States that the AVERO Phoenix lifting bath tub is not suitable for sterilization.
Advises recycling packaging materials according to local regulations, with metal/plastic/electronic components recycled per WEEE.
Recommends contacting the dealer for product recycling at end-of-life and notes cleaning/disinfection before disposal.
Provides a table listing common problems with the bath tub and their suggested remedies.
Lists detailed technical specifications including dimensions, weights, electrical data, operating elements, and ambient conditions.
Presents detailed technical drawings and dimensions for the AVERO Phoenix 190 model.
Presents detailed technical drawings and dimensions for the AVERO Phoenix 170 model.
Includes a wiring diagram and pre-site safety measures for connecting the bath tub's sanitary and electrical components.
Contains the EC Declaration of Conformity for the AVERO Phoenix, referencing relevant EU directives and standards.
Lists available accessories for the AVERO Phoenix, identified by article numbers and descriptions.
Informs that spare parts and consumables are available from the dealer or manufacturer and require specialist installation.
Details EMC guidance, manufacturer declarations, and immunity testing for the AVERO Phoenix.
Provides a template for keeping a device journal as required by the Medical Device Directive, including training records.
General| Category | Medical Equipment |
|---|---|
| Manufacturer | Beka Hospitec |
| Model | AVERO Phoenix |
| Trendelenburg/Reverse Trendelenburg | Yes |
| Safe Working Load | 200 kg |
To Next Page
