Beko WMB 51421 - Starting the programme; Child Lock

68
EN
ProgrammeSelectionknobtoanyprogramme.
Thus,DelayedStartfunctionwillbecanceled.The
End/Cancellightflashescontinuously.Then,select
theprogrammeyouwanttorunagain.PressStart
/Pausebuttontostarttheprogramme.
Starting the programme
PressStart/Pausebuttontostarttheprogramme.
Programmefollow-uplightshowingthestartupof
theprogrammewillturnon.
C
 Ifnoprogrammeisstartedornokeyis
pressedwithin1minuteduringprogramme
selectionprocess,themachinewillswitch
toPausemodeandtheilluminationlevelof
the temperature, speed and loading door
indicatorlightswilldecrease.Otherindicator
lightsandindicatorswillturnoff.Oncethe
ProgrammeSelectionknobisrotatedor
any button is pressed, indicator lights and
indicatorswillturnonagain.
Child Lock
Usechildlockfunctiontopreventchildrenfrom
tamperingwiththemachine.Thusyoucanavoid
any changes in a running programme.
C
 IftheProgrammeSelectionknobisrotated
whenthechildlockisactive,thelightsonthe
1
st
and 2
nd
auxiliaryfunctionbuttonswillblink
3times.Thechildlockdoesnotallowany
change in the programmes and the selected
temperature,speedandauxiliaryfunctions.
C
 Evenifanotherprogrammeisselectedwith
theProgrammeSelectionknobwhiletheChild
Lockisactive,previouslyselectedprogramme
willcontinuerunning.
C
 WhentheChildLockisactiveandthe
machineisrunning,youcanswitchthe
machinetoPausemodewithoutdeactivating
theChildLockbyturningtheProgramme
SelectionknobtoOn/Offposition.When
youturntheProgrammeSelectionknob
afterwards,theprogrammewillresume.
ToactivatetheChildLock:
Pressandhold1
st
and 2
nd
Auxiliary Function
buttonsfor3seconds.Thelightsonthe1
st
and 2
nd
AuxiliaryFunctionbuttonswillflashwhileyoukeep
thebuttonspressedfor3seconds.
TodeactivatetheChildLock:
Pressandhold1
st
and 2
nd
auxiliaryfunction
buttonsfor3secondswhileanyprogrammeis
running.Thelightsonthe1
st
and 2
nd
Auxiliary
Functionbuttonswillflashwhileyoukeepthe
buttonspressedfor3seconds.
C
 Inadditiontothemethodabove,todeactivate
theChildLock,switchtheProgramme
SelectionknobtoOn/Offpositionwhenno
programme is running, and select another
programme.
C
 Whenthepowerisrestoredafterapower
failureorafteryourmachineisunplugged
andpluggedinagain,theChildLockwillnot
bedeactivatedwhenthemachineresumes
operating.
Progress of programme
Progressofarunningprogrammecanbefollowed
fromtheProgrammeFollow-upindicator.At
thebeginningofeveryprogrammestep,the
relevantindicatorlightwillturnonandlightofthe
completedstepwillturnoff.
Youcanchangetheauxiliaryfunctions,speed
andtemperaturesettingswithoutstoppingthe
programmeflowwhiletheprogrammeisrunning.
Todothis,thechangeyouaregoingtomakemust
beinastepaftertherunningprogrammestep.If
thechangeisnotcompatible,relevantlightswill
flashfor3times.
C
 Ifthemachinedoesnotpasstothespinning
step,RinseHoldfunctionmightbeactive
or the automatic unbalanced load detection
system might be activated due to the
unbalanceddistributionofthelaundryinthe
machine.
Loading door lock
Thereisalockingsystemontheloadingdoorof
themachinethatpreventsopeningofthedoorin
caseswhenthewaterlevelisunsuitable.
Loadingdoorlightwillstartflashingwhenthe
machineisswitchedtoPausemode.Machine
checksthelevelofthewaterinside.Ifthelevelis
suitable,LoadingDoorlightilluminatessteadily
within1-2minutesandtheloadingdoorcanbe
opened.
Ifthelevelisunsuitable,LoadingDoorlightturns
offandtheloadingdoorcannotbeopened.If
youareobligedtoopentheLoadingDoorwhile
theLoadingDoorlightisoff,youhavetocancel
the current programme; see "Canceling the
programme".
Changing the selections after
programme has started
Switching the machine to pause mode
PresstheStart/Pausebuttontoswitchthe
machinetopausemodewhileaprogrammeis
running.Thelightofthestepwhichthemachine
isinstartsflashingintheProgrammeFollow-up
indicatortoshowthatthemachinehasbeen
switchedtothepausemode.
Also,whentheloadingdoorisreadytobeopened,
LoadingDoorlightwillalsoilluminatecontinuously
in addition to the programme step light.
Changing the speed and temperature settings
for auxiliary functions
Dependingonthesteptheprogrammehas
reached, you may cancel or activate the auxiliary
functions;see,"Auxiliaryfunctionselection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
C
 Ifnochangeisallowed,therelevantlightwill
flashfor3times.