Why is my laundry still wet after the Beko WMP 11744 XWR cycle is complete?
If your laundry remains wet after the programme ends on your Beko Washer, it's possible that excessive foam has occurred, activating the automatic foam absorption system due to using too much detergent. Use the recommended amount of detergent.
Why is my Beko WMP 11744 XWR leaking from the bottom?
If you notice water leaking from the bottom of your Beko Washer, it could be due to a clogged or twisted water drain hose; try cleaning or flattening the hose. Another possible cause is a clogged pump filter, which will need to be cleaned.
Why won't my Beko WMP 11744 XWR go to the spinning cycle?
If your Beko Washer isn't spinning, it could be due to an unbalanced load. The automatic unbalanced load detection system might be activated. Also, the product won't spin if water isn't completely drained, so check the filter and draining hose. Excessive foam from using too much detergent can also prevent spinning; use the recommended amount of detergent.
Why doesn't my Beko WMP 11744 XWR rinse clothes properly?
If your Beko Washer isn't rinsing well, the issue might be with the detergent. Ensure you're using a detergent appropriate for washing machines and your laundry, and store it properly. Also, check that detergent isn't placed in the wrong compartment. Make sure the pump filter and drain hose are not clogged or folded.
How to fix a Beko WMP 11744 XWR Washer that won't take in water?
If your Beko Washer isn't taking in water, there are several possible reasons. First, check to ensure that the tap is turned on. Next, inspect the water inlet hose to see if it is bent and flatten it if necessary. Also, the water inlet filter might be clogged, so clean it. Finally, make sure that the loading door is completely closed.
What to do if my Beko WMP 11744 XWR Washer stopped soon after starting?
Your Beko Washer may have stopped temporarily due to low voltage. The product will resume running when the voltage restores to the normal level.
What to do if foam overflows from the Beko Washer detergent drawer?
If foam is overflowing from the detergent drawer of your Beko Washer, it is most likely caused by using too much detergent. To address this, mix 1 tablespoonful of softener with ½ liter of water and pour it into the main wash compartment of the detergent drawer.
Why are there oily stains on my clothes after washing in my Beko WMP 11744 XWR Washer?
If oily stains appear on your laundry after washing in your Beko Washer, it may be because regular drum cleaning is not being performed. Clean the drum regularly.
Why is there detergent residue in my Beko WMP 11744 XWR's drawer?
If you're finding detergent residue in the drawer of your Beko Washer, ensure the drawer is dry before adding detergent. The detergent may have gotten damp, so keep detergents closed in a humidity-free environment and avoid high temperatures. Low water pressure might also be a factor; check the water pressure. Also, check the holes of the detergent compartment and clean them if they are blocked. Ensure you're not mixing softener with detergent, and wash the drawer with hot water. Regular drum cleaning is also important.
Why are my clothes turning gray after washing in my Beko WMP 11744 XWR Washer?
If your laundry is turning gray after washing in your Beko Washer, it could be due to using too little detergent over a long period. Make sure to use the recommended amount of detergent appropriate for water hardness and the laundry. Also, washing at low temperatures for a long time can cause this issue, so select the proper temperature for the laundry. Insufficient detergent with hard water can also cause graying; use the recommended amount. Using too much detergent can also contribute to this problem; use the recommended amount.
To Next Page
General
