What to do if Status LED is steady red on Belden Grass Valley Kaleido-Modular-X Monitor?
If the Status LED on your Belden Monitor is steadily red (not flashing), it indicates that the firmware initialization or update is in progress. To resolve this, do not interrupt the process.
How to fix a flashing red Status LED on Belden Grass Valley Kaleido-Modular-X?
If the Status LED on your Belden Monitor is flashing red, it indicates a fan failure or no rear. Check the fan or the rear of the device to solve this problem.
Why is the SDI LED red on my Belden Monitor?
If the SDI LED on your Belden Monitor is red, this indicates that no input signal has been detected. To resolve this, verify the input signal.
What does it mean when the REF LED is red on a Belden Grass Valley Kaleido-Modular-X Monitor?
If the REF LED is red on your Belden Monitor, it means no signal has been detected. You should verify the REF input signal.
What should I do if the ABT LED is red on my Belden Monitor?
If the ABT LED on your Belden Monitor is red, this indicates that no signal has been detected. To resolve this, verify the ABT/MADI signal.
How to troubleshoot a Belden Monitor with Power LED OFF?
If the Power LED is OFF on your Belden Monitor, it suggests a failure of the 1.8V or 3.3V on-board PSUs. Check the power supplies to resolve this issue.
General| Humidity | 10% to 90% non-condensing |
|---|---|
| Type | Multiviewer |
| Display Type | Modular |
| Screen Size | Various (Modular) |
| Video Inputs | SDI, HDMI |
| Video Outputs | SDI, HDMI |
| Supported Formats | SD, HD, 3G-SDI, UHD |
| Audio Inputs | Embedded Audio |
| Audio Outputs | Embedded Audio |
| Control Interfaces | Ethernet |
| Power Supply | 100-240V AC, 50/60Hz |
| Dimensions | Varies with configuration |
| Form Factor | Modular |
| Input Interfaces | SDI, HDMI |
| Mounting Options | Rack-mountable |
| Operating Temperature | 0 to 40°C |
| Storage Temperature | -20 to 60°C |
Legal notices regarding copyright and trademarks.
Outlines the terms of use for product documentation.
Lists standards for electromagnetic compatibility.
Addresses compliance with environmental regulations.
Lists other relevant documentation for the system.
Details the key features of the Kaleido-Modular-X system.
Explains module interconnection and system configurations.
Initial steps for unpacking and preparing the system.
Lists necessary tools and components for installation.
Details specific interface types for Densité frames.
Explains FlexBridge connections between input and output cards.
Details FlexBridge cabling for IP-based configurations.
Details how to connect input and output signals.
Steps to convert input cards to/from 4K UHD prescaler mode.
Details front panel interfaces and troubleshooting for cards.
Guides on operating the Densité frame's local control panel.
Covers assigning IP addresses to system components.
Steps to configure network settings for different system types.
Describes how to check the system's operational status.
Checks status and settings for RCP2, ABT, IP addresses.
Guides on how to replace cards in the frame.
Guides on replacing power supply modules in the frame.
Information on diagnosing and replacing cooling fans.
Important considerations and tasks before performing an upgrade.
Detailed steps for upgrading the system via USB.
Steps to resolve issues with failed software upgrades.
Lists requirements for the client PC used for configuration.
Guides on installing, uninstalling, and accessing XEdit.
Guides on installing and uninstalling Router Control.
Guides on installing and uninstalling Signal Path Viewer.
Lists different methods to access XAdmin.
Steps to open XAdmin using a web browser.
How to register security credentials with browser to avoid warnings.
Steps to enable password protection for XAdmin.
Steps to change the XAdmin password.
Steps to disable password protection for XAdmin access.
Describes the control panels for cards within iControl.
Panel for configuring network settings of the IPG-3901 module.
Panel for configuring IPG-3901 gateway settings.
Panel for configuring reference settings for the IPG-3901 module.
Guides on configuring the KMX-3901-IN-IP module.
How to set a unique name for the multiviewer system.
Explains the reasons and methods for genlocking the multiviewer.
Guides on setting up the RCP-200 remote control panel.
Guides on setting up the Kaleido-RCP2 remote control panel.
Guides on setting up the Audio Bridge Terminal (ABT).
Details available software options for input cards.
Details available software options for output cards.
Technical specifications for KMX-3901-IN input cards.
Details of video input signal specifications.
Specifications for SD-SDI video inputs.
Specifications for HD-SDI video inputs.
Specifications for 3G-SDI video inputs.
Details for discrete audio input specifications.
Specifications for MADI audio inputs.
Specifications for FlexBridge connections.
Specifications for reference signal inputs.
Specifications for LTC time code inputs.
Electrical specifications, including power consumption.
Physical characteristics like temperature, humidity, and weight.
Specifications for the 4K UHD prescaler card.
Technical specifications for KMX-3901-OUT output cards.
Details for mosaic output specifications.
Specifications for HDMI output connections.
Specifications for SDI monitoring outputs.
Specifications for analog audio output connections.
Communication interface specifications.
Specifications for the serial port connection.
Specifications for the USB port.
Specifications for the GPI-1501 module.
Services for establishing communication with other devices.
Lists optional drivers for controlling routing devices.
Lists optional drivers for controlling tally interface devices.
Lists optional drivers for scoreboards and timers.
Details built-in communication protocols supported by the multiviewer.
To Next Page
