Benassi BL 6000 - Use and Adjustment; Spur Adjustment; Transfer Wheel Adjustment

SpA BL6000
6
Pict.8
A
B
D C
AB
C
Pict.9
USEANDADJUSTMENT
• Thetillerisequippedwithamechanicaltransmissionthatallowstwoforwardspeedsandonereverse.
• Whenthe machineis standstillto moveforwardsimplyengagethe gearlever(Pict.7 Ref.“A”) inthe firstor inthe second speed
(Pict.7Ref.“B”)andthenpressdowncompletelythe
lever(Pict.6bRef.“A”)tostartthemovement.
• Whenthemachine isstandstilltomovebackwards engagethegearlever(Pict.7Ref.“A”) intheposition“R”(Pict.7Ref.“B”) and
thenpressdowncompletelythelever(Pict.6bRef.“A”)tostartthemovement.
• Theclutchcable must
beadjustedin awaythatallowsthebeltto beputundertensionwhenthelever issituatedatabout1cm
fromtheknob.Tothispurposeyouhavetoregulatethe registerofthecablenexttothelever(Ref.“B”Pict.6).
• Whenthelever(Pict.6bRef.
“A”)isreleasedthemachinestopsimmediatelywhiletheengineisrunning. 
• Thehandlebarcanbeadjustedbyunscrewingtheblockinglever(Pict.6Ref.“C”).Adjustthehandlebarinthedesiredpositionand
thenlockitagain.
• Thetilleris80cmwide,itiscomposedby3
knives+protectionplate onbothsides.Itcanbereducedto60cmbyremovingone
bladefromeachsides(seepicture2).
• Thesharpsideofthebladesmustbeturnedtowardsthefrontsideofthemachine.
• Werecommendtousethetillerwiththeside
platesbecausetheyimprovethestabilityofthemachinewhileworking.
• Themachinecanfit an adjustableridgerwhichisanoptional accessorydeliveredcompletewithitsown supportwhichshouldbe
fittedonthehandlebarholderreplacingthestandardspurandusingthesamebolt.
CAUTION:ITISADVICEDNOTTOKEEPTHEMOTORRUNNINGWHENTHEMACHINEISNOT BEINGUSEDFOR
ITSSPECIFICALPURPOSE.

SPURADJUSTMENT
Togetanoptimaltillingworkanda rightadvancementofthetilleradjustthespurasshownin
picture8,thisadjustmenthastobedoneonbothsidesofthemachine:
− Adjustment for hard soils: loosen nut and  screw(A) and lift the  spur as to shift back
 the
weightofthemachine.
− Adjustment for soft soils: loosen nut and screw (A) and lower the spur as to move the
weightofthemachinetowardsthebladesaxle.
Toenablethe tillertomove slightlysidewaysduringthe tillingwork,thespurholderarm
(B)canbe
adjustedhorizontallyasfollows:
a. loosenthenut(C)andadjustthescrew(D)asdesired,thentightenthenutagain.Bytighteningthescrew(D)thespurcanmovesi‐
deways.
b. carryoutthesameadjustmentalsoontheothersideofthearm.

TRANSFERWHEELADJUSTMENT
Totransferthemachinethesmal ltransferwheelhastobelowered(seepicture9).Beforeworkingremovethesplintpin
(B)andtheclampingpin(A),liftupthesmal ltransferwheel(C)andinserttheclampingpin(A)againin
thelowerhole.Theclampingpinalwayshasto
belockedinthedesiredpositionbymeansofthe
splintpin(B).


A
B
Pict.7