EasyManua.ls Logo

BenQ MS513P - User Manual

BenQ MS513P
57 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Welcome
MS513P/MX514P Digital Projector
User Manual

Table of Contents

Questions and Answers

  • T
    Tonya Hodge MDJul 29, 2025
    What to do if my BenQ Digital projector has no picture?
    • C
      christina03Jul 29, 2025
      If your BenQ Digital projector displays no picture, there are several potential causes: * The video source might not be turned on or correctly connected. Ensure the video source is on and the signal cable is properly connected. * The projector may not be correctly connected to the input signal device. Check the connection. * The input signal might not be correctly selected. Use the SOURCE key on the projector or remote control to select the correct input signal. * The lens cover might still be closed. Open the lens cover.
  • T
    Todd PerezAug 5, 2025
    How to fix if my BenQ Digital projector does not turn on?
    • B
      bryan94Aug 5, 2025
      If your BenQ Digital projector doesn't turn on, here are a couple of things to check: * Ensure the power cord is properly plugged into both the AC power jack on the projector and a working power outlet. If the outlet has a switch, make sure it's on. * If you've recently tried turning it on, the projector might be cooling down. Wait until the cooling process is complete before attempting to turn it on again.
  • S
    Samuel KellyAug 12, 2025
    Why is my BenQ Digital projector image blurred and how to fix it?
    • J
      jlittleAug 12, 2025
      If you're experiencing a blurred image with your BenQ Digital projector, consider these potential causes: * The projection lens might not be correctly focused. Adjust the focus of the lens using the focus ring. * The projector and screen may not be aligned properly. Adjust the projection angle, direction, and height of the projector if needed. * The lens cover might still be closed. Open the lens cover.
  • A
    Austin SmithAug 20, 2025
    What to do if BenQ Digital projector remote control does not work?
    • T
      Thomas JohnsonAug 20, 2025
      If the remote control for your BenQ Digital projector isn't working, try these solutions: * The battery may be out of power. Replace it with a new one. * There might be an obstacle between the remote and the projector. Remove any obstructions. * You might be too far from the projector. Ensure you are within 8 meters (26 feet) of the projector.

Summary

Important safety instructions

Introduction

Projector features

Lists the key features of the projector, highlighting its capabilities and user-friendliness.

Shipping contents

Projector exterior view

Controls and functions

Explains the buttons and functions on the projector's control panel.

Remote control

Describes the functions of each button on the projector's remote control.

Connection

Connecting video source devices

Explains how to connect various video source devices using different connection methods like HDMI, Component, S-Video, and Video.

Operation

Starting up the projector

Guides the user through the initial power-on sequence and setup.

Adjusting the projected image

Covers adjusting projector angle, auto-adjustment, zoom, and focus for optimal image quality.

Correcting keystone

Explains how to fix image distortion caused by non-perpendicular projector placement.

Using the menus

Provides an overview of the On-Screen Display (OSD) menus and how to navigate them.

Securing the projector

Details how to use a security cable lock and set up a password for unauthorized access prevention.

If you forget the password

Explains procedures for password recovery and recall if the password is forgotten.

Changing the password

Guides users on how to change or disable the projector's password security settings.

Switching input signal

Describes how to select the active input source for the projector.

Selecting the aspect ratio

Optimizing the image

Covers adjusting wall color and selecting picture modes for optimal image quality.

Setting the User 1;User 2 mode

Fine-tuning the image quality in user modes

Locking control keys

Shutting down the projector

Step-by-step instructions for properly turning off the projector, including cooling procedures.

Menu operation

Menu system

DISPLAY menu

PICTURE menu

SOURCE menu

SYSTEM SETUP: Basic menu

SYSTEM SETUP: Advanced menu

Maintenance

Care of the projector

Lamp information

Extending lamp life

Timing of replacing the lamp

Describes lamp warning indicators and messages that prompt lamp replacement.

Replacing the lamp

Provides detailed, step-by-step instructions for safely replacing the projector lamp.

Resetting the lamp timer

Troubleshooting

The projector does not turn on

Lists common causes and remedies for the projector failing to power on.

No picture

Provides solutions for issues where the projector displays no image or a blank screen.

Blurred image

Offers steps to resolve problems with a blurry or out-of-focus projected image.

Remote control does not work

The password is incorrect

BenQ MS513P Specifications

General IconGeneral
Number of colors1.073 billion colors
Projection distance- m
Vertical scan range23 - 120 Hz
Horizontal scan range31 - 102 kHz
Projection technologyDLP
Contrast ratio (dynamic)13000:1
Contrast ratio (typical)-
Screen size compatibility40 - 300 \
Projector native resolutionSVGA (800x600)
Keystone correction, vertical±40 °
RS-232 ports1
Offset120 %
Throw ratio1.86 - 2.04:1
Zoom capabilityYes
Focal length range21 - 23.1 mm
Aperture range (F-F)2.57 - 2.65
Lamp power190 W
Light source typeLamp
Service life of light source4500 h
Service life of light source (economic mode)6000 h
Full HDNo
Supported video modes1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format systemNTSC, PAL, SECAM
Supported graphics resolutions1600 x 1200 (UXGA), 640 x 480 (VGA)
RMS rated power2 W
Headphone outputs2
Serial interface typeRS-232
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity3
Component video (YPbPr/YCbCr) in0
Noise level30 dB
Noise level (economic mode)26 dB
On Screen Display (OSD) languagesARA, BUL, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, FIN, FRE, GRE, HUN, ITA, JPN, KOR, POL, POR, RUM, RUS, SWE, THA, TUR
Product colorBlack
Cables includedAC, VGA
Power sourceAC
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (standby)- W
Power consumption (typical)265 W
Weight and Dimensions IconWeight and Dimensions
Depth232.6 mm
Width287.3 mm
Height114.4 mm
Weight2500 g

Related product manuals