11
What’s on the first TV tuning menu…
Freq (frequency)... Searching stops at the first
station producing an acceptable signal. If this is
not the station you want, press
▲ or ▼ again to
continue searching. If you know a station’s exact
frequency number, key it in directly using the
number buttons.
(System)… If System appears on the menu, make
sure that the correct broadcast system is displayed
before you start tuning:
B/G... for PAL/SECAM B/G
I... for PAL I
L... for SECAM L
M... for NTSC
D/K... for PAL/SECAM D/K
Note: All options may not always be displayed as
it depends on the broadcast systems available for
the various countries.
Pr (program number)... Key in the program
number (1-99) you wish to preset the station on.
Name (naming)... The name you give a station
will appear in the TV program list.
A name may contain up to ten characters,
including the letters A-Z, numbers and full stop.
When the item is lit up in red, start ‘writing’:
Press
▲ or ▼ to reveal the character you want.
Press 0 to switch from upper to lower case, or vice
versa. Then press
tt to move on to the next
character position. Continue ‘writing’ the name
using this method.
Then press GO or move on to More... When
you have entered the information you want, press
GO to store your TV program or….
More… If it is necessary to fill in extra
information, move to More and press GO. A
second TV tuning menu appears for fine tuning,
availability of decoder and type of sound. When
you have filled in the necessary information,
pressing GO stores it and returns you to the first
tuning menu.
What’s on the second TV tuning menu…
Fine (fine tuning)... The TV automatically tunes to
the best possible picture. However, neighbouring
channels may blur the picture slightly, in which
case fine tuning may be required. You fine tune
by 8 steps above or below the standard frequency.
Decoder... A decoder can be connected to the
BeoVision Avant for the reception of coded TV
programs.
If you tune in a coded TV station and want the
decoder to be cut in automatically, set the item
Decoder to one of the On options below:
ON/AV... (decoder on) where both audio and
video signals are coded
ON/V... (decoder on) where only video signals
are coded
OFF... (decoder off) for no decoder
Select ON/AV for most coded programs to get
both sound and pictures. If only the video signal is
coded, select ON/V. If you select ON/AV where
only the video signal is coded, the sound may be
lost when the signal is decoded.
Note: If an extra decoder is connected to the
BeoVision Avant AV socket and Decoder-2 is
entered into the AV Source menu ( see page 50,
Extra video equipment), you can choose between
1/AV or 1/V, for decoder-1, and 2/AV or 2/V for
decoder-2 or OFF for no decoder.
Sound (mono/stereo/language)... Several types of
sound may available for a TV station, for example
both stereo and mono sound, or several different
languages.
To store the type of sound (mono/stereo) or the
language you prefer along with a TV station,
press
▲ or ▼ to switch between the ones currently
transmitted, when the sound you wish to store is
heard/displayed, press GO.
Note: Even though you store your preferred type
of sound/language in this way, you may still
switch between the various types of sound while
you are watching this TV station.
Press LIST to display SOUND* on the Beo4 remote
control, then press GO repeatedly to switch
sound. See page 35, Switching sound for more
information about the various types of sound
available.
*Note: In order to display SOUND on Beo4, you
must add the function to the Beo4 LIST function,
see Extra functions in Beo4, page 67.
Removing a tuned TV station…
Press MENU to call up the main menu, press 3
to select TV list and press GO to call up the TV
program list, use the
▲ and ▼ buttons to
move the cursor to the station you want to
remove. Then press MENU. When Clr? appears,
press GO to clear the program. See Program
list, page 25, for further information.
To Next Page
Loading...
