To Next Page
M
Manuel GrossJul 27, 2025
What to do if my Beretta EXCLUSIVE shows an operating fault?
- JJoshua WhiteJul 27, 2025
If there is an operating fault with your Beretta Boiler, wait approximately 10 seconds before resetting the operating conditions.
What to do if my Beretta EXCLUSIVE shows an operating fault?
If there is an operating fault with your Beretta Boiler, wait approximately 10 seconds before resetting the operating conditions.
Lists key sections like User's Manual, boiler elements, circuits, and diagrams.
Explains symbols used for warnings, prohibitions, and important notes.
Covers care, wiring, and the manual's role as an integral part of the product.
Details requirements for qualified personnel, annual servicing, and installer instructions.
Outlines manufacturer liability, appliance purpose, and packaging handling.
Covers safety valve, modifications, fault handling, user info, shutdown, and general measures.
Lists the different boiler models and their types (e.g., Combined, CH only).
Specifies where the boiler can or cannot be installed.
Provides guidelines on minimum spaces, insulation, and flammable substances.
Details CH/DHW connection points, dimensions, and associated specifications.
Recommends using softeners for hard water to prevent limestone deposits.
Ensures compliance with regulations, correct gas type, and pipe cleanliness.
Covers wall passage for pipes and recommendations for using a filter.
Provides steps to access the unit's electrical terminals for connection.
Details mains power supply, earthing requirements, and power cable specifications.
Step-by-step guide for filling the system and achieving correct pressure.
Procedures for emptying domestic hot water and central heating circuits.
Instructions for connecting the safety valve outlet to a collection system.
Details various configurations (C12-C82x) and general rules for fume extraction.
Installation guidelines, graphs, and condensate collector requirements for Ø 60-100 outlets.
Guidelines, table, condensate trap, and slope requirements for Ø 80-125 outlets.
Installation guidelines, tables, and condensate requirements for twin outlets.
Information on maximum duct lengths and pressure drop for bends.
Details nominal and reduced heating and domestic hot water capacities.
Covers working efficiency, electrical power consumption, and protection levels.
Provides data on pressure, temperature, pump, and tank specifications for CH/DHW.
Specifies gas pressure, connection types, and pipe sizes.
Lists physical dimensions, weight, and fan head performance data.
Details fume pipe diameters, lengths, and emission values (NOx, CO).
Details Wobbe index, heat value, and nominal/minimum gas supply pressures.
Specifies gas capacities and pressures for 24 kW and 28 kW models.
Specifies gas capacities and pressures for 26 kW, 30 kW, and 35 kW models.
Describes the control panel layout, buttons, and their functions.
Explains the various icons and symbols displayed on the boiler's control panel.
Guides through the initial power-up sequence and test procedure.
Details how to set heating water temperature manually or via an external sensor.
Explains how to set the domestic hot water temperature.
Describes normal boiler operation, safety stops, and fault code display.
Procedure for temporary shutdown, including anti-freeze and anti-block systems.
Instructions for shutting down the boiler for extended periods.
Details the semi-automatic filling device and its operation.
Explains the S.A.R.A. Booster and Domestic Hot Water Preheating functions.
Details how the S.A.R.A. self-adjustment system operates for comfort and energy saving.
Provides a table listing fault codes, alarm status, and corresponding symbols.
Step-by-step guide for clearing detected faults and resuming operation.
Instructions on how to enter the parameter programming mode.
Procedure for setting or entering the password to access parameter modifications.
Guides on how to select, modify, and confirm parameter values.
Parameters related to gas type, building insulation, and DHW/CH operating modes.
Parameters for heating power reduction, timers, and reset functions.
Parameters for DHW thermostat, preheating, S.A.R.A., and thermoregulation.
Parameters for antifreeze function temperatures and filling settings.
Explains the three operating cases for R.A.I./MIX R.S.I. boilers.
Describes the control panel layout, buttons, and their functions for R.A.I./MIX R.S.I.
Explains the various icons and symbols for R.A.I./MIX R.S.I. boilers.
Guides through the initial power-up sequence and test procedure for R.A.I./MIX R.S.I.
Details setting heating water temperature manually or via an external sensor.
Explains how to set domestic hot water temperature for specific cases.
Describes normal operation, safety stops, and fault code display for R.A.I./MIX R.S.I.
Instructions for temporary and prolonged shutdown procedures.
Details the procedure for filling the heating circuit and restoring pressure.
General