Pod Model: introduce the coffee pod into the single-
spout filter holder (Fig. 02; pos. 17).
Ground Coffee Model: introduce the ground coffee
with the proper measuring spoon (Fig. 02; pos.
20), into the filter holder (Fig. 02; pos. 18) with
one or two-cup filter (Fig. 02; pos. 21/1-2) de-
pending on the desired number of coffees; even-
tually press the coffee powder by applying a slight
pressure with the appropriate tamper (Fig. 02;
pos. 19).
3) Reconnect the filter holder to the assembly (Fig.
01; pos. 2).
4) Place the cup under the coffee delivery spout (Fig.
01; pos. 12).
5) Press the coffee switch (Fig. 01; pos. 9) until the
desired coffee quantity is reached.
6) Press the coffee switch (Fig. 01; pos. 9) again to
stop delivery.
Warnings:
- Do not remove the filter-holder when the appliance
is working, the delivery assembly is pressurized.
- Do not touch directly the metal part of the filter
holder because it is hot.
5.4 Hot water delivery
Failure to close the tap after normal opera-
tion can result in damages to the heating
element for which the Manufacturer is not
responsible.
During the following procedure the hot wa-
ter delivery from the assembly is usual
1) Place a container under the steam/water delivery
pipe (Fig. 01; pos. 3).
2) Open the steam/water tap (Fig. 01; pos. 1) and
press the coffee switch (Fig. 01; pos. 9).
3) After delivering the desired amount of water, close
the steam/water tap (Fig. 01; pos. 1) and press
the coffee switch (Fig. 01; pos. 9) again.
5.5 Steam delivery
Failure to close the tap after normal opera-
tion can result in damages to the heating
element for which the Manufacturer is not
responsible.
For steam delivery perform the following operations:
1) Press the steam switch (Fig. 01; pos. 10), turning
on of the red (Fig. 01; pos.11) and orange (Fig 1;
pos.15) leds.
2) Open the steam/water tap (Fig. 01; pos. 1), dis-
charge water for about 10 seconds (Fig. 01; pos.
3), in order to partially empty the boiler to allow
the expansion of the steam volume.
3) Close the steam/water tap (Fig. 01; pos. 1) and
wait until the orange led (Fig. 01; pos. 15) is
switched off.
4) Dip the steam/water delivery pipe (Fig. 01; pos. 3)
into the drink to heat and open the steam/water
tap (Fig. 01; pos. 1).
5) After heating the drink, discharge a little steam to
clean out the sprayer hole.
6) Close the steam/water tap (Fig. 01; pos. 1) and
press the steam switch (Fig. 01; pos. 10), turning
off of the red and orange (Fig. 01, pos.11/13)
leds to stop the steam function
After each steam delivery, you need to fill
the boiler as follows:
During the following procedure the hot wa-
ter delivery from the assembly is usual
1) Check that the steam switch (Fig. 01; pos. 10) is in
Off position, red led off (Fig.1, pos. 11).
2) Place a container under the steam/water delivery
pipe (Fig. 01; pos. 3).
3) Open the steam/water tap (Fig. 01; pos. 1).
4) Press the coffee switch (Fig. 01; pos. 9) up to the
delivery with continuous flow of water from the
steam/water delivery pipe (Fig. 01; pos. 3).
5) Press the coffee switch (Fig. 01; pos. 9) and close
the steam/water tap (Fig. 01; pos. 1).
The machine is ready for normal operation.
5.6 Switching off
Press the main switch (Fig. 01; pos. 14).
Should the machine be off for long periods:
1) empty the tank,
2) unplug from power supply,
3) replace the machine in a dry, weather-resistant
environment of exclusive access.
To Next Page
Loading...
