BGS technic 3287 - User Manual

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0
F 56 essartS resukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni :liaM-E diehcsmeR 79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: 02196 720480
Fax.: 02196 7204820
mail@bgs-technic.de
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
Art. 3287
Air Grinder / Cut Off Tool
TECHNICAL DATA
Cutting Disc Diameter: Ø 75 mm
Cutting Disc Bore: Ø 10 mm
Working Pressure: 6,3 Bar (90 PSI)
Air Inlet: 1/4"
max. Speed: 18000 U/min (18000 RPM)
Noise Level: LpA: = 87 dB (A)
LwA:= 98 dB (A)
Vibration Level: ahd = 1.68 m/s²
Length: 310 mm
Safety rules
1. Always wear approved eye protection.
2. Have throttle (trigger) in "on" position when connecting to air supply.
3. Disconnect tool before performing service or when not in use.
4. Always use tool in a safe distance from other people in work area.
5. Maintain tools with care. Keep tools clean and oiled for best and safest performance. Follow
instructions for lubricating and changing accessories. Wiping or cleaning rags and other
flammable waste materials must be placed in a lightly closed metal container and disposed of later
in the proper fashion.
6. Do not wear loose or ill-fitting clothing, remove matches and rings.
7. Never use quick change couplings at tool. They add weight and could fail due to vibration. Instead
add a hose whip and connect coupling between air supply and hose whip or between hose whip
and leader hose.
8. Don't overreach, keep proper footing and balance at all times.
9. Don't force tool. It will do the job better and safer at the rate for which it was designed.
10. Don't abuse hoses or connectors. Never carry tool by the hose or yank it to disconnect from power
supply. Keep hoses from heat oil and sharp edges. Check hoses for weak or worn condition
before each use making certain that all connections are secure.
11. When possible secure work with clamps or vise so both hands are free to operate tool.
12. Accessory retainers should be used to prevent discard or ejection of the accessory which might
injure persons in the general area. Switch of tool when changing location or on transport. Never
carry the tool when trigger is depressed or when cutting wheel is still moving. Accessory should be
removed when tool is not in use.

Summary

Technical Specifications and Safety

Technical Data

Details on cutting disc diameter, bore, working pressure, air inlet, speed, noise, vibration, and length.

Safety Rules

12 essential safety rules for operating the air grinder, covering eye protection, tool handling, and maintenance.

Air Supply and Operation

Air Supply

Recommendations for air pressure, hose diameter, and hook-up procedures for optimal tool performance.

Operating Instructions

Guidance on using the regulator, oiling the tool daily, and proper cutting techniques for efficiency.

Attention and Maintenance

Attention

Crucial safety reminders regarding protective gear and cutting disc RPM ratings.

Lubrication and Maintenance

Daily lubrication requirements and troubleshooting for power loss or erratic operation.

Declaration of Conformity

EU Declaration of Conformity

Official statement confirming the Air Grinder/Cut Off Tool complies with Machinery Directive 2006/42/EC.

Applied Standards

Lists the relevant standards, including EN ISO 11148-7:2012, and verification details.

BGS technic 3287 Specifications

General

Brand	BGS technic
Model	3287
Category	Grinder
Language	English