Black & Decker 598667-00

Questions and Answers

D
Dustin BuchananAug 12, 2025
Why won't my Black & Decker 598667-00 motor start?
- H
  hsandersAug 12, 2025
  The motor may not start for several reasons: the unit isn't plugged in (plug in the power cord); the On/Off switch is in the Off position (turn the switch to the “On” position); the gun trigger isn't being squeezed (squeeze the gun trigger with the switch in the “ON” position); or the GFCI has tripped (press the reset button at the GFCI on the plug end of the cord).
M
Miranda MooreAug 16, 2025
What to do if my Black & Decker 598667-00 Pressure Washer doesn't reach high pressure?
- S
  Stephanie BoothAug 16, 2025
  If your pressure washer isn't reaching high pressure, several factors could be responsible. First, ensure the water faucet is fully turned on. Second, check the water inlet filter for clogs and rinse it clean. Also, inspect the garden hose for any kinks, leaks, or blockages that may be restricting the water supply. Finally, make sure that hoses and fittings are airtight, and purge the pump by squeezing the gun trigger until a steady flow of water emerges from the nozzle.
C
Crystal MillerAug 20, 2025
How to fix a leaking garden hose connection on my Black & Decker Pressure Washer?
- D
  duncankarenAug 20, 2025
  If your garden hose connection is leaking, it could be due to loose fittings or a missing/worn rubber washer. Try tightening the fittings first. If that doesn't solve the problem, replace the washer in the hose adapter.
T
Timothy GuerreroAug 23, 2025
What to do if my Black & Decker 598667-00 Pressure Washer motor buzzes but fails to run?
- P
  patrick40Aug 23, 2025
  If the motor buzzes but fails to run, it could be due to several reasons. First, verify that ONLY the pressure washer is running on the circuit, as the supply voltage may be below the minimum. Second, the system may have residual pressure; turn the unit off, squeeze the gun trigger to release pressure, then turn the unit back on. Finally, avoid using an extension cord with the unit and plug it directly into the outlet.
H
Holly ThompsonAug 27, 2025
Why is the output pressure of my Black & Decker Pressure Washer varying high and low?
- A
  Anna ChoiAug 27, 2025
  The output pressure may vary if there is not enough inlet water supply or if the pump is sucking air. To resolve this, turn the water on full force and check the garden hose for leaks and kinks. Also, ensure that hoses and fittings are airtight and purge the pump by squeezing the gun trigger until a steady flow of water emerges from the nozzle.
K
Kelly NicholsonAug 31, 2025
How to troubleshoot excessive noise from my Black & Decker 598667-00 pump?
- W
  Wayne GrayAug 31, 2025
  If the pump is excessively noisy, it may be sucking air. Check that hoses and fittings are airtight. Turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges from the nozzle.
T
twardSep 4, 2025
Why is there no detergent coming out of my Black & Decker 598667-00 Pressure Washer?
- W
  williamstamaraSep 4, 2025
  If there is no detergent, make sure that the adjustable fan wand nozzle tip is pulled forward and the turbo wand is not installed. Add more detergent, using only detergents recommended for pressure washers. Fill the tank with warm water and allow the filter to soak, then empty and refill with clean water several times to rinse the filter. Remove any debris with the provided tool.
M
Miss Priscilla RamosSep 7, 2025
What causes a Black & Decker 598667-00 spray wand or extension to leak?
- A
  Amanda PorterSep 8, 2025
  A spray wand or extension can leak if the spray wand is not properly attached. Insert the spray wand into the wand extension and push in and turn to lock it into place.