Black & Decker BDPS400

Questions and Answers

J
Joseph LawsonJul 30, 2025
Why is little or no material being released from my Black & Decker BDPS400 Paint Sprayer?
- J
  jessica71Jul 30, 2025
  If little or no material is coming out of your Black & Decker Paint Sprayer, here are a few things to check: * The spray nozzle/tip may be clogged, so try cleaning the nozzles. * The pickup tube might be loose or clogged; inspect and check the tube. * The flow control knob setting could be too low; increase the flow control setting. * The material might be too thick; check the viscosity recommendation.
G
Gina WatsonAug 3, 2025
What to do if my Black & Decker BDPS400 motor works but it does not spray?
- M
  Mrs. Ashley CohenAug 3, 2025
  If the motor of your Black & Decker Paint Sprayer is running but it's not spraying, consider the following: * Prime the sprayer with remote tubing by thinning the spray material, holding the sprayer below the level of the spray material can, and oiling the intake opening. * Check for a loose or damaged suction tube; thin or replace if necessary. * Inspect the atomizer valve for clogs or wear; clean or replace as needed. * Ensure the atomizer valve is present; put in the atomizer valve if missing. * If the material is too thick, thin it. * Clean a plugged spray tip. * Clean a plugged intake filter. * Adjust the control knob. * Clean and oil or replace a worn piston.
S
saramitchellAug 7, 2025
How to stop my Black & Decker BDPS400 Paint Sprayer from running or dripping?
- J
  Justin PrestonAug 7, 2025
  If your Black & Decker Paint Sprayer is running or dripping, it could be due to several reasons: * You might be spraying too much material; reduce the airflow by turning the material adjustment knob. * You might be spraying too slowly; increase your application speed. * You might be spraying too close to the surface; increase the distance from the surface. * The viscosity of the material might be too thin; check the dilution recommendation.
L
Luis WilliamsonAug 12, 2025
How to reduce over spray with Black & Decker BDPS400?
- J
  Jeffery EspinozaAug 12, 2025
  To reduce over spray with your Black & Decker Paint Sprayer: * If the sprayer is too far from the surface, reduce the distance to the surface. * If too much material is being sprayed, reduce the flow by turning the flow control knob clockwise.
R
Ryan SmithAug 16, 2025
Why is liquid coming out the side of the canister of my Black & Decker BDPS400 Paint Sprayer?
- L
  Leslie RhodesAug 16, 2025
  If liquid is coming out the side of the canister of your Black & Decker Paint Sprayer: * The lid might not be on square or tight enough; remove the lid and reattach squarely and evenly, then tighten the lid securely. * There might be paint on the threads of the canister and lid; clean the threads on top and sides of the canister and lid.
K
Kenneth CarrollAug 20, 2025
Why is the material splattering from my Black & Decker BDPS400 Paint Sprayer?
- E
  Elijah StewartAug 21, 2025
  If the material being sprayed from your Black & Decker Paint Sprayer is splattering, the viscosity of the material might be too low. Thin the material per the manufacturer's recommendation.
G
gardnermelindaAug 25, 2025
Why does my Black & Decker BDPS400 pulsate?
- M
  Margaret OrtizAug 25, 2025
  Your Black & Decker Paint Sprayer may pulsate if the material in the canister is almost empty. Refill the canister.