Black & Decker PPRH5B

Questions and Answers

S
Stacy WeissAug 13, 2025
What to do if my Black & Decker PPRH5B Remote Starter fails to jump-start?
- A
  Alicia CraigAug 13, 2025
  If your Black & Decker Remote Starter fails to jump-start, ensure the jump-starter power switch is in the on position. Also, check that the unit has a full charge and recharge if needed. Finally, verify that a proper polarity cable connection has been established.
M
Melissa WhiteAug 17, 2025
How to charge my Black & Decker Remote Starter?
- P
  Patrick JacobsonAug 17, 2025
  To charge your Black & Decker Remote Starter, first, make sure the inverter power switch is in the off position. Next, ensure a suitable gauge extension cord is properly connected to both the unit and a functioning AC outlet. Also, check that the 12 volt DC charger is properly connected to both the unit and a functioning DC power source.
J
Janice JonesAug 21, 2025
What to do if Black & Decker Power Supply USB port not working?
- D
  Dr. Tony Jones PhDAug 21, 2025
  If the USB power port on your Black & Decker Power Supply isn't working, ensure that the USB device plugged in doesn't exceed a 2A draw. Also, verify that the AC/USB power button is pressed to activate the USB ports. Some USB-powered devices might not be compatible with this type of USB charging/power port, so check your device's manual. Finally, check the power supply's charge level and recharge if needed.
D
Dave MathisAug 25, 2025
Why Black & Decker Power Supply portable compressor won't inflate?
- D
  Dawn ParkAug 26, 2025
  If the portable compressor on your Black & Decker Power Supply isn't inflating, check the following: * Make sure the unit is not in Jump Starter mode. * Ensure the compressor power button is pressed to turn the compressor on. * Verify the Sure Fit® nozzle connector is securely attached to the valve stem or that the nozzle adapter is properly inserted into the item you're trying to inflate. Also, the compressor may be overheated, so turn it off and allow it to cool down for about 30 minutes before restarting. Finally, ensure the unit has a full charge and recharge it if necessary.
L
Laurie TranAug 28, 2025
What to do if the 120 volt AC outlet on my Black & Decker PPRH5B Remote Starter will not power an appliance?
- P
  patrick57Aug 28, 2025
  If the 120 volt AC outlet on your Black & Decker Remote Starter isn't powering an appliance, first, ensure the inverter power switch is in the on position. Then, carefully follow all steps in the 120 AC portable power supply instructions. Lastly, check that the unit has a full charge and recharge if necessary.
V
Valerie BlackSep 1, 2025
Why won't the portable compressor on my Black & Decker PPRH5B inflate?
- D
  Debbie BeltranSep 1, 2025
  If the portable compressor on your Black & Decker Remote Starter won't inflate, ensure the compressor power switch is in the on position. Also, make sure the SureFit® nozzle connector is securely screwed onto the valve stem. If it still doesn't work, the compressor may be overheated, so turn it off. As well, check that the unit has a full charge and recharge it if necessary.
E
Erik VelezSep 4, 2025
What to do if the 12 volt DC accessory outlet on my Black & Decker Remote Starter doesn't power my appliance?
- C
  Christopher BrownSep 5, 2025
  If the 12 volt DC accessory outlet on your Black & Decker Remote Starter is not powering your appliance, make sure the appliance does not draw more than 5 amps. Also, check that the unit has a full charge and recharge it if necessary.
M
Megan WheelerSep 8, 2025
Why is the USB power port on my Black & Decker Remote Starter not working?
- E
  Erin CummingsSep 8, 2025
  If the USB power port on your Black & Decker Remote Starter is not working, ensure the USB power button is in the on position. Also, verify that the appliance being powered does not draw more than 2,000mA. Note that some USB-powered household electronics may not operate with this USB charging/power port. Finally, check that the unit has a full charge and recharge if necessary.