BLACKSTONEPRODUCTS.COM/SUPPORT
ENGLISH
| OWNER’S MANUALUSING YOUR BLACKSTONE
CONNECT THE LPG CYLINDER
ONLY USE A 20 LB (9 KG) CYLINDER
STEP 01
Turn the control
knobs to OFF.
❶
Ensure that the LPG cylinder
is OFF by turning the OPD hand
wheel clockwise to a full stop.
❷
Remove the safety cap from
the Type 1 valve outlet.
STEP 02
Hold the regulator in a
straight line with the Type 1 valve
outlet so as not to cross thread
the connection.
Center and insert the regu-
lator nipple into the Type 1
valve outlet.
Hand-tighten the coupling nut in
a clockwise direction.
(DO NOT use tools to connect.)
If connection cannot be completed,
If connection cannot be completed,
disconnect regulator and repeat this
disconnect regulator and repeat this
step.
LEAK TEST: VALVES, HOSE & REGULATOR
STEP 01
Turn the control knobs to OFF.
STEP 02
Connect the regulator to the LPG cylinder.
STEP 03
Completely open the LPG tank by turning the OPD hand
wheel counterclockwise.
• If you hear a rushing sound, turn gas o immediately. There is a
major leak at the connection.
• Immediately close the LPG cylinder by turning the OPD hand wheel
clockwise and re-tighten connections. If leaks cannot be stopped
DO NOT TRY TO REPAIR.
STEP 04
Use a clean paintbrush
to brush a mild soap and
water solutionn onto joint areas
of valves and regulator.
(Indicated by arrows in figure 02.)
(Indicated by arrows in figure 02.)
• Leaks are indicated by
growing bubbles.
• Immediately close the LPG
cylinder by turning the OPD
hand wheel clockwise and
re-tighten connections.
WARNING
If leaks cannot be stopped, DO NOT try to repair.
Regulator must be replaced with a Blackstone approved
model by a professionally licensed, authorized dealer.
The safety relief valve must face
away from the user while the
appliance is in use.
DISCONNECTING THE LPG CYLINDER
STEP 01
Ensure that the control knobs are turned to OFF.
❶
Ensure that the LPG cylinder
is OFF by turning the OPD hand
wheel clockwise to a full stop.
❷
Turn the coupling nut count-
er-clockwise by hand to remove
the regulator. (DO NOT use tools
to disconnect.)
STEP 02
Place dust cap on LPG
cylinder valve outlet whenever
cylinder is not in use.
Only install the type of dust cap on
Only install the type of dust cap on
cylinder valve outlet that is provided
cylinder valve outlet that is provided
with the cylinder valve. Other types of
with the cylinder valve. Other types of
caps or plugs may result in leakage of
caps or plugs may result in leakage of
propane.
REGULATOR SAFETY
• Use this appliance, as purchased, only with gas and regulator/
valve assembly supplied. DO NOT use quick connect fittings or
other add-ons.
• DO NOT cross thread (force at an improper angle) the connection
between your LPG cylinder and regulator.
• If you can not connect the regulator, DO NOT use the regulator.
Regulator must be replaced with a Blackstone approved model by a profession-
Regulator must be replaced with a Blackstone approved model by a profession-
ally licensed, authorized dealer.
ally licensed, authorized dealer.
❷
Coupling nutCoupling nut
Regulator nippleRegulator nipple
figure 02
❷
ADAPTER HOSE INSTRUCTIONS
ONLY USE A 20 LB (9 KG) CYLINDER
The Blackstone Adapter Hose is
used to connect a 20 lb (9 kg)
LPG cylinder to an appliance that
uses a 1 lb (453 g) LPG cylinder.
The 20 lb (9 kg) LPG cylinder must be
The 20 lb (9 kg) LPG cylinder must be
closed before connecting the adapter
closed before connecting the adapter
hose.
STEP 01
Connect the adapter
hose to the gas rail.
STEP 03
Once the LPG cylinder
has been connected to the
adapter hose, be sure that the
LPG cylinder is placed where
neither the cylinder or the hose
will be a tripping hazard.
MODELS: 2321 • 2321CA
To Next Page
Loading...
